Cart 2 india

Specification
Brand : TGB
BulletPoint : ER308L Stainless Steel MIG Welding Wire 2-Lb Spool .030" & .035"
BulletPoint1 : For welding 18% chromium – 12% nickel – 2½% molybdenum austenitic stainless steels such as 316 and 317 but with a low ferrite (i.e. FN2) it can also be used for welding 304/304L to 316/316L stainless steels in cryogenic service at temperatures down to -452 °F
BulletPoint2 : The maximum carbon content of less than 0.03% preserves the intergranular corrosion resistant properties of the weld deposit and weld zone, yielding x-ray quality welds. The 2½% molybdenum content of 316L gives the weld deposit excellent corrosion resistance at elevated temperatures against “pitting” that may be caused by sulfuric, phosphoric and acetic acids.
BulletPoint3 : Common applications include equipment that manufacturers rayon, dye, paper, ink, rubber, bleach, photographic chemicals and on the sealing faces of valves and fittings for acid, gas, water and steam equipment.
BulletPoint4 : Spool Weight: 2 Lb of Wire - Available Sizes: 0.030"and 0.035" - Spool Quantity Packs: 1 Spool, 2 Spools, 4 Spools, and 6 Spools
BulletPoint5 : For shielding gas use 100% Argon or Argon/Helium for greater penetration and higher speeds
Color : Silver
CustomerPackageType : Standard Packaging
ExternallyAssignedProductIdentifier1 : 703856605862
ExternallyAssignedProductIdentifier2 : 0703856605862
ExternallyAssignedProductIdentifier3 : 00684032586840
ExternallyAssignedProductIdentifier4 : 0607872515382
ExternallyAssignedProductIdentifier5 : 00716352144032
FinishType : Smooth
GpsrSafetyAttestation : 1
HeatingElementType : Mica
IncludedComponents : Wire
ItemDisplayWeight : 2 pounds
ItemForm : Rod
ItemName : ER316L - MIG Stainless Steel Welding Wire - 2 Lb x 0.035"
ItemPackageDimensions_Height : 2.8 inches
ItemPackageDimensions_Length : 7 inches
ItemPackageDimensions_Width : 7 inches
ItemPackageQuantity : 1
ItemShape : Cylindrical
ItemTypeKeyword : welding-wire
Manufacturer : TGB
Material : Stainless Steel
MeasurementSystem : English
ModelNumber : QU-Aluminum Rods-F1-50cm*1.6mm-30 Pcs
NumberOfBoxes : 1
NumberOfItems : 30
PackageLevel : unit
PartNumber : 316LW2x35
ProductDescription : ER316L - WIRE - MIG (GMAW) - STAINLESS STEEL AWS A5.9 Welding Positions: All INTRODUCTION: The main component of ER316L is 18Cr-12Ni-2Mo. It is an all position welding MIG Wire. The weld-ability is good. Feeding wire smoothly will enable stable arc, excellent welding performance and spatter is very low. It has good resistance for acetic acid, sulfuric acid, phosphoric acid and salt corrosion because it contains Molybdenum. USES: It is widely used in petrochemical, chemical fertilizer equipment such as 022Cr17Ni12Mo2 (SUS 316L) and other materials of welding. CHEMICAL COMPOSITION (%): Chemical Composition C Mn Si Cr Ni Requirement ?0.030 1.00~2.50 0.30~0.65 18..00~20.00 11.00~14.00 Typical test result 0.023 1.90 0.42 19.12 12.59 Chemical Composition Mo P S Cu Requirement 2.00~3.00 ?0.030 ?0.030 ?0.75 Typical test result 2.59 0.009 0.008 0.28 WELDING PARAMETERS (DC+): Diameter (mm) ?0.8 ?1.0 ?1.2 Welding Current (Amps) 70~150 100~200 140~220 NOTES: 1. Shield gas: Must ensure not to operate with impurity shield Gas, Recommended Rate of mixed gas: Ar + 1-3% O2. 2. Operation flow rate of shield gas: 20-25L/min. 3. Electrode extension: 15-25mm 4. The welding should be operated in clean surface without rust, moist, oil contamination and dust. 5. To avoid bubbles protect from wind its speed reach 1.5 m/s. The above parameters are for reference purpose and depend on diverse factors. Run tests, evaluate and set your welding parameters before starting the welding job.
ProductSiteLaunchDate : 2017-01-25T21:56:21.976Z
Size : 0.035" - (1 Spool)
SpecificUsesForProduct : Residential Use
Style : fashion
SupplierDeclaredDgHzRegulation : not_applicable
UnitCount : 1
UnspscCode : 23271800
Voltage : 549 volts