Cart 2 india

Specification
Brand : Scientific Commodities
BulletPoint1 : Hydrophilic
BulletPoint2 : Manufactured in the United States
BulletPoint3 : Among the most rigid of thermoforming materials with a modulus of elasticity of 2,482 MPa (360,000 psi)
BulletPoint4 : Easy to form with excellent part definition and deep-draw characteristics
BulletPoint5 : Great for knife sheaths and gun holsters
BulletPoint6 : Lightweight and sturdy
BulletPoint7 : Does not darken or deteriorate from exposure to fluorescent light
BulletPoint8 : Easy to clean and polish
Color : Black, 52114, P3 Velour Matte
CustomerPackageType : Standard Packaging
ExternallyAssignedProductIdentifier : 00810064985683
ExternallyAssignedProductIdentifier1 : 788703923467
ExternallyAssignedProductIdentifier2 : 0788703923467
IncludedComponents : rubber strip
ItemDisplayWeight : 1 pounds
ItemForm : Sheet
ItemName : UHMW (Ultra High Molecular Weight) Polyethylene Porous Tube/Average Pore Size: 10 Micron/Hydrophilic/Dimensions: 1/2" OD x 1/4" ID x 12" Long / (1 Tube)
ItemPackageDimensions_Height : 1.27 centimeters
ItemPackageDimensions_Length : 29.972 centimeters
ItemPackageDimensions_Width : 30.48 centimeters
ItemPackageQuantity : 1
ItemShape : Sheet
ItemTypeKeyword : plastic-tubes
Manufacturer : Genpore
Material : UHMW Polyethylene
ModelNumber : BB2062-1412AL
NumberOfItems : 1
PackageLevel : unit
PartNumber : BB2062-1412AL
ProductDescription : KYDEX V
KYDEX V sheet has excellent forming properties, which results in uniform wall thicknesses and crisp detail. KYDEX V sheet forms to deep draws with low forces when heated to the upper end of the forming temperature range. Unlike many other thermoforming sheets, KYDEX V sheet has unusually high resistance to hot tearing.

Forming Guidelines
- Oven temperatures should be set differently than the settings used for ABS or FR-ABS.

- Typical heater settings (percentage timers) are 30% – 50% top heaters and 50% - 70% bottom heaters.
- The most frequent problem is trying to heat the sheet too quickly, particularly on the primary surface.
- Cycle times will vary depending on the oven conditions and grade of KYDEX V sheet being formed.
- When forming KYDEX V sheet, it is better to rely on the sheet appearance during heating than on fixed cycle times.
- Forming temperatures – Guidelines: (Sheet should not exceed 204°C (400°F).

165 - 177°C (330 - 350°F) for < 1.50mm (0.060").
182 - 196°C (360 - 385°F) for 1.50mm to 3.20mm (0.060" to 0.125").
196 - 204°C (385 - 400°F) for > 3.20mm (0.125")

- Ideally the core sheet temperature should be within 10°F of the surface temperature.

Sheet Appearance During Heating
As KYDEX V sheet is heated, the inherent stresses in the sheet will relax.

Stage I: The heating is marked by wide undulations and softening.

Stage II: The material will start to form small ripples (known as oil canning). .

Stage III: The material will start to smooth out and sag (KYDEX V sheet will generally sag less than other thermoplastics due to its high melt strength. .

Stage IV: The ripples will have smoothed out indicating that most stresses have been removed. 10 to 30 seconds afterwards the sheet is ready to form.
ProductSiteLaunchDate : 2018-08-01T07:00:00.000Z
RecommendedUsesForProduct : Gasket, Surface Protection, Sealing
Size : 8 Pack - .060", Size - 12" x 12"
Style : Cast
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
UnitCount : 8
UnspscCode : 41000000