Cart 2 india

Specification
Brand : Sea-Dog
BulletPoint : Great Product
BulletPoint1 : High Impact Resistance
BulletPoint2 : Saltwater/Freshwater Resistant
BulletPoint3 : Excellent adhesion to Wood, Steel, Aluminum, Soft Metals, Concrete, Ceramic, Fiberglass, Composites
BulletPoint4 : Low Shrinkage; Withstands Wide Range of Temperatures
BulletPoint5 : Can be Mixed with Sand to Create a High Strength Mortar for Concrete Repair
CircuitType : 1-way
Color : Metal
ConnectivityProtocol : X-10
ConnectorType : Screw Terminals
ControllerType : Ring
ControlMethod : touch
CustomerPackageType : 1
Department : unisex-adult
ExteriorFinish : Copper
ExternallyAssignedProductIdentifier1 : 035514404853
ExternallyAssignedProductIdentifier2 : 0035514404853
Hazmat : auto-grounding
ImportDesignation : Made in the USA
IncludedComponents : Great Product
ItemName : Sea-Dog LED Touch Dimmer Switch f/Aurora Pop-Up Table Lamp
ItemPackageDimensions_Height : 14 centimeters
ItemPackageDimensions_Length : 2.9 centimeters
ItemPackageDimensions_Width : 7 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : boating-tools
Manufacturer : Sea-Dog
Material : Stainless Steel
ModelName : 403061-1
ModelNumber : 403061-1
MountingType : Wall Mount
NumberOfItems : 1
OperationMode : Manual
PackageLevel : unit
PartNumber : 403061-1
Pattern : Solid
ProductDescription : 103 LVX Epoxy laminating epoxy is a new and improved formula. It provides high tensile strength while maintaining a very low viscosity to aid in wetting out fiberglass. This enables the laminator to produce high tensile strength lay-ups with maximum “wetting out” and a minimum of bubbles.
103 LVX can be used on warehouse docks, floors, sidewalks, walls, and concrete. 103 LVX can be mixed with sand to fill in large holes and cracks in concrete and has enough strength to withstand heavy forklift traffic. 103 LVX seals against leaks without shrinkage and is also used to laminate fiberglass cloth to existing fiberglass, wood, metal, or concrete.

Application: Mix very well, scraping down the sides of the mixing bucket to ensure that all of the resin and hardener gets mixed together.
Application for Heavy Duty Non-Skid Surface for Metal, Concrete, Wood, or Fiberglass:
1. Surface must be clean, dry, and free from oil or grease.
2. Mix the 103 LVX kit. Roll or brush evenly on surface.
3. While epoxy is wet, broadcast quartz aggregate evenly on surface (other non-skid particles may be substituted for quartz). The epoxy should stay wet enough to receive the aggregate for at least 1 hour. Use aggregate size in accordance to roughness desired - #30-65 aggregate is an average non-skid surface.
4. Continue above procedure until entire surface is covered with aggregate.
5. Allow to dry. Sweep off loose aggregate.
6. Apply a thin coat of mixed 103 LVX epoxy over the aggregate surface. Squeegee the epoxy down tight so that there are no puddles of epoxy. The surface should have an even textured appearance.
Working Time: Mixed product must be used within 30 min.
Gel Time Thin Coats 4-6 hours - Thick Coats 2-4 Hours.
Set Time Thin Coats 6-8 hours - Thick Coats 4-6 Hours.
Cure Time 24 to 72 Hours
ProductSiteLaunchDate : 2019-12-05T00:32:31.119Z
Size : One Size
SpecificationMet : Etl, Ip67
SupplierDeclaredDgHzRegulation : not_applicable
SwitchType1 : Dimmer
SwitchType2 : Touch
TerminalType : Screw
UnitCount : 1
UnspscCode : 39122200
VolumeCapacityName : 3 quarts
WarrantyDescription : Warranty
Wattage : 36 watts