Cart 2 india

Specification
Brand : Aoaoy
BulletPoint : Quantity Of (1000) Per Package
BulletPoint1 : Inserts will form a high‑strength, wear‑resistant, high‑accuracy standard female thread if you fit the wire screw set in the screw hole of the workpiece of aluminum alloy and other materials
BulletPoint2 : You can repairing the threaded hole in a cost‑effective manner when a thread error occurs or a damaged female threaded hole is repaired
BulletPoint3 : The product can be used to convert between metric and inch thread holes, which is convenient and fast
BulletPoint4 : Using high‑strength, high‑accuracy ‑shaped cross‑section steel wire. Wire thread inserts are also called threaded sheaths, stainless steel threaded sleeves, wire sleeves, a new type of female threaded fasteners
BulletPoint5 : Used on low‑strength engineering materials like aluminum alloy, zinc alloy, alloy, copper, plastic, engineering plastics, etc. can improve thread strength and wear significantly
ItemName : Thread Reducing Nut,10Pcs Thread Inserts Male Female Reducing Nut Repair Tool Stainless Steel Wire Fastener M18x2.5 (1D)
ItemPackageDimensions_Height : 2 centimeters
ItemPackageDimensions_Length : 7 centimeters
ItemPackageDimensions_Width : 6 centimeters
ItemPackageQuantity : 1000
ItemTypeKeyword : threading-inserts
Manufacturer : Aoaoy
Material : Stainless Steel
ModelName : Aoaoyrz2q7ab3xe-11
ModelNumber : Aoaoyrz2q7ab3xe-11
NumberOfItems : 1000
PartNumber : Aoaoyrz2q7ab3xe-11
ProductDescription : Specification:
Item Type: Thread Inserts
Material: SUS304
Model: M18x2.5
Thread Specification: M18x2.5 (mm)
Outside Diameter Before Installation: Approx. 21.4 ~ 22mm / 0.8 ~ 0.9in
Diameter of Drilling Drill Bit for Installation: Approx. 18.6mm / 0.7in1D/1.5D/2D/2.5D/3D:
Length After Installation: Approx. 18mm / 0.7in
27mm / 1.1in
36mm / 1.4in
45mm / 1.8in
54mm / 2.1in
Number of Turns Before Installation: 5.6/9/12.3/15.7/19
Specification Description: For Example: M3x0.5X1.5D, which means that after the screw set is completed, the female thread is M3, the pitch is 0.5, and the length is 1.5D (length refers to 1.5 times the diameter, that is, 1.5x3=4.5mm ), the length here refers to the length after installation.
How to Use:
1. Drilling
Use the drill bit of the size listed in the parameter table of the wire thread insert to drill the hole. Be careful not to drill the hole into a cone shape. The chips generated by the drill hole must be blown out with compressed air. After drilling, the counterbore should not exceed the depth of 0.4 pitch. Too large counterbore is not conducive to the screwing of the wire thread insert.
2. Tapping
Use special taps for wire thread inserts to tap. The depth of the tapping must exceed the installation length of the thread inserts. After tapping, use a compressed air spray to blow out the debris. When the thread accuracy is high, check the tapped bottom hole with a special bottom hole plug for wire thread inserts.
3. Installation
Put the wire screw sleeve into the installation wrench (figure 5 on the right), insert the wire screw sleeve installation tail handle into the rod groove of the installation wrench, and turn the handle of the installation wrench to screw the wire screw sleeve into the screw hole. For installation of M14x2 or more phase thread thread inserts, you can use the T type slotting simple tool to
ProductSiteLaunchDate : 2025-05-19T22:06:48.779Z
Size : 1D