Cart 2 india

Specification
Brand : DAOKAI
BulletPoint1 : WHAT IT DOES: This temperature and humidity sensor can detect air temperature and humidity with a microcontroller and output it on the computer.
BulletPoint2 : NUMERICAL ACCURACY: GY-SHT31 Temperature/Humidity sensors are some of the finest and highest-accuracy devices you can get and it has an excellent ±2% relative humidity and ±0.3°C accuracy for most uses.
BulletPoint3 : WIDE VOLTAGE: Wide supply voltage range of 2.5 V to 5.5 V ensures compatibility with a wide range of assembly conditions.So you can use any microcontroller or microcomputer to power and communicate.
BulletPoint4 : ADVANTAGES: A combination of multiple functions and various interfaces (I2C, voltage output) and a friendly, wide operating voltage range.These sensors are suitable for a variety of high-volume and small-volume applications.
BulletPoint5 : PIN DESCRIPTION: Vin - power pin;SCL - I2C clock pin;SDA - I2C data pin;ADR - I2C address selection pin;RST - Hardware reset pint;ALR - Alert/Interrupt output.
BulletPoint6 : NOTICE: To power the board, give it the same power as the logic level of your microcontroller-eg for a 5V micro, use 5V.For a 3.3V controller, connect to 3.3V GND-common ground for power and logic.
BulletPoint7 : PRODUCTS INCLUDE: 1 x SHT31-D Sensor Module;1 x 4-pin header;10 x Male and female cable.
CircuitBreakerType : Standard
Color : SHT31-D
CurrentRating : 1 amps
ExternallyAssignedProductIdentifier1 : 0742779302823
ExternallyAssignedProductIdentifier2 : 742779302823
IncludedComponents : 1 x SHT31-D Sensor Module kit
ItemName : DAOKAI Temperature and Humidity Sensor Module SHT31 SHT31-D IIC I2C Interface Digital Output 3.3V 5V with Male and Female Cables for Arduino
ItemPackageDimensions_Height : 15.6 centimeters
ItemPackageDimensions_Length : 1.5 centimeters
ItemPackageDimensions_Width : 5.4 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : industrial-temperature-sensors
Manufacturer : DAOKAI
Material : Copper
ModelNumber : JA-DA-052
MountingType : Surface Mount
NumberOfItems : 1
NumberOfPoles : 1
PartNumber : JA-DA-052
ProductDescription : The SHT31-D sensor has an excellent ±2% relative humidity and ±0.3°C accuracy for most uses.Unlike earlier SHT sensors, this sensor has a true I2C interface, and even with two address options.It also is 3V or 5V compliant,so you can power and communicate with it using just about any microcontroller or microcomputer.

Specification:
RH response time: 0-100% RH
Interface: I2C
Colour:Purple
Material:Plastic
Pins:
Vin - this is the power pin.The chip can use 2.5-5VDC for power.To power the board, give it the same power as the level of your microcontroller - e.g.for a 5V Mini like for , use 5V.For a 3.3V controller like a Pi, connect to 3.3V GND - common ground for power and logic.
SCL - I2C clock pin, connect to your microcontrollers I2C clock line.This pin has a 10K pullup resistor to Vin.
SDA - I2C data pin, connect to your microcontrollers I2C data line.This pin has a 10K pullup resistor to Vin.
ADR - This is the I2C address selection pin.This pin has a 10K pull down resistor to make the default I2C address 0x44.You can tie this pin to Vin to make the address 0x45.
RST - Hardware reset pint.Has a 10K pullup on it to make the chip active by default.Connect to ground to do a hardware reset.
ALR - Alert/Interrupt output.You can set up the sensor to alert you when an event has occured.

Package Includes:
1 x SHT31-D Sensor Module
1 x 4-pin header
10 x Male and female cable
ProductSiteLaunchDate : 2024-03-30T09:49:34.789Z
Style : Modern
SupplierDeclaredDgHzRegulation : not_applicable
UnitCount : 1
UnspscCode : 39121601
Voltage : 3.3 volts