Cart 2 india

Specification
ActiveSurfaceArea : 8x10 inches
AdditionalPrinterFunctions : print_only
AgeRangeDescription : Adult
Brand : DGT Tattoo Supply
BulletPoint1 : WX1+ with the ring switch on/off ,Voltage Output: 6, 7, 8 ,9, 11V, .Charging Voltage DC5V/1A, Input: TYPE-C
BulletPoint2 : Battery Capacity: 1450MAH, 4.Dual charge and discharge protection (Battery built-in over-surge protection, control board with short circuit over-surge over-discharge protection more safe.)
BulletPoint3 : Press power button for 2 seconds to turn on machine, 6.Press up/down button to change the voltage, voltage goes in a cycle from: 5V-12V, Pass the up/down button for 3 seconds for the jump start (H) (L) seting
BulletPoint4 : Once machine is turned on, there will be a quick jump start at 10V, after 0.2 seconds machine will automatically resume to the last used voltage
BulletPoint5 : This product does not allow charging and running the machine at the same time, If short-circuit protection occurs during use, just plug into the charger and it will activate automatically
Color : Black
CompatibleDevices : PC
ConnectivityTechnology : Wi-Fi
ConnectivityTechnology1 : Bluetooth
ConnectivityTechnology2 : USB
ControllerType1 : Android
ControllerType2 : iOS
ControlMethod : application
Directions : Press power button for 2 seconds to turn on machine, press up/down button to change voltage (5V-12V cycle), press up/down button for 3 seconds for jump start (H) (L) setting, charge via DC5V/1A TYPE-C port, do not charge and run simultaneously, reactivate after short-circuit protection by charging.
Duplex : simplex
ExternallyAssignedProductIdentifier1 : 793811108125
ExternallyAssignedProductIdentifier2 : 0793811108125
IncludedComponents : M08F Thermal Tattoo Printer, 45 Sheets of Tattoo Transfer Paper
IsHeatSensitive : 1
ItemName : DGT WX-1Plus Tattoo Machine Battery with Jump start mode and Ring on/off switch RCA CONNECTOR
ItemPackageDimensions_Height : 2.5 inches
ItemPackageDimensions_Length : 9 inches
ItemPackageDimensions_Width : 2.5 inches
ItemPackageQuantity : 1
ItemTypeKeyword : tattoo-machines
Lifestyle : Premium Beauty
Manufacturer : DGT Tattoo Supply
Material : Plastic
Material1 : Plastic
Material2 : Aluminum
MaxCopyResolutionBlackWhite : 600 dpi
MaximumCopiesPerRun : 1
MaxInputSheetCapacity : 45
MaxPrintResolutionBlackWhite : 1200 dpi
MaxPrintResolutionColor : 300 dpi
MediaSizeMaximum : A4
ModelName : M08F
ModelNumber : WX-1Plus
ModelSeries : M08F
NumberOfDrivers : 1
NumberOfItems : 1
NumberOfPieces : 1
NumberOfTrays : 1
OperationMode : Automatic
PaperSize : A4 [NA]
PartNumber : TM99-1076-06RCA
Pattern : Solid
PrinterOutput : Monochrome
PrinterTechnology : Thermal
PrintMediaType : paper_plain
ProcessorCount : 1
ProductBenefit : Easy to use, charge fast and lightweight
ProductDescription : The WX1+ tattoo machine features a ring switch for on/off control and offers voltage outputs of 6V, 7V, 8V, 9V, and 11V. It charges via a DC5V/1A input using a TYPE-C port and has a 1450mAh battery. The device includes dual charge and discharge protection, with built-in over-surge protection and a control board that safeguards against short circuits, over-surges, and over-discharges. To operate, press the power button for 2 seconds to turn on the machine, and use the up/down buttons to adjust the voltage in a cycle from 5V to 12V. A 3-second press of the up/down button initiates a jump start. Upon activation, the machine quickly starts at 10V, then reverts to the last used voltage after 0.2 seconds. In sleep mode, the battery display appears 2 seconds after pressing the power button, with light indicators showing the remaining battery percentage (20%-100%). Press the power button again to resume voltage adjustment. During charging, the light indicator flashes and turns solid when charging is complete, entering "protection" mode. The battery, with a capacity of 1450mAh, charges fully in approximately 3.5 hours, providing up to 8 hours of work time at voltages below 8V. Designed primarily for rotary tattoo machines, the WX1+ should not be used with coil machines and does not support simultaneous charging and operation. In case of short-circuit protection, simply plug the device into the charger to reactivate it.
ProductSiteLaunchDate : 2019-12-10T08:00:00.000Z
Resolution : 1200 x 1200
SafetyWarning : Read Instructions Manual
ShortProductDescription : The WX1+ tattoo machine features a ring switch for on/off control and voltage outputs of 6V, 7V, 8V, 9V, and 11V. It charges via a DC5V/1A TYPE-C port with a 1450mAh battery. The device includes dual charge and discharge protection with built-in safeguards. To operate, press the power button for 2 seconds to turn it on, use the up/down buttons to cycle voltage from 5V to 12V, and press for 3 seconds to jump start. The machine starts at 10V, then reverts to the last used voltage after 0.2 seconds. In sleep mode, the battery display shows after 2 seconds, with light indicators for battery percentage (20%-100%). During charging, the indicator flashes and turns solid when complete. The battery charges in 3.5 hours and lasts up to 8 hours at voltages below 8V. Designed for rotary tattoo machines, the WX1+ should not be used with coil machines and doesn't support simultaneous charging and operation. For short-circuit protection, plug into the charger to reactivate.
SpecificUsesForProduct : Tattooing
Style : Compact
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
TargetAudienceKeyword : Unisex Adult
TargetAudienceKeyword1 : Unisex Adult
TargetAudienceKeyword2 : Tattoo artists
TargetAudienceKeyword3 : Unisex Adult
UnitCount : 1
UnspscCode : 53131800
WarrantyType : limited warranty
WaterResistanceLevel : not_water_resistant