Cart 2 india

Specification
Brand : SÜA
BulletPoint : These electrodes are suitable for welding carbon steel and low-alloy steel in structural steel
BulletPoint1 : All position welding of 18% Cr – 12% Ni – 2½% Mo stainless steel producing weld deposits with a carbon content of 0.04% maximum
BulletPoint2 : ***READ THIS: The images are for reference only. Please check Picture #2 for an approximate quantity of electrodes per pound***
BulletPoint3 : When this electrode produces a weld deposit of 2 FN maximum, it can be used for welding 304 and 316 stainless steels in cryogenic service at temperatures down to -452 °F. Excellent corrosion resistance at elevated temperatures against “pitting” that may be caused by sulfuric, phosphoric and acetic acids.
BulletPoint4 : Can be used for welding ferritic-austenitic stainless steel such as 329, 405, 410, and 430 or titanium/niobium stabilized grades such as 316Ti in certain applications where the service temperature is below 750 °F. Common applications involve those industries manufacturing rayon, dye, paper, ink, rubber, bleach, photographic chemicals; also used for building up the sealing faces of valves and fittings for acid, gas, water, and steam equipment.
BulletPoint5 : These Electrodes are available in Sizes: 3/32" and 1/8" - Available Packages: 0.5 Lb, 2 Lb and 4.4 Lb - Select your option from the Size Menu - Check Picture #2 for an approximate number of electrodes per pound - 3/32" electrodes are 12" long and 1/8" electrodes are 14" long
Color : As Shown
ExternallyAssignedProductIdentifier : 00840338563415
ExternallyAssignedProductIdentifier1 : 015082517681
ExternallyAssignedProductIdentifier2 : 0015082517681
ItemDisplayWeight : 2 pounds
ItemName : SÜA® - E316L-16 - Stainless Steel Welding Electrode - 14" x 1/8" (2 LB)
ItemPackageDimensions_Height : 15 inches
ItemPackageDimensions_Length : 6 inches
ItemPackageDimensions_Width : 6 inches
ItemPackageQuantity : 1
ItemTypeKeyword : arc-welding-stick-electrodes
Manufacturer : Mundaka Technologies Inc
Material : Stainless Steel
ModelNumber : LINED028702
NumberOfItems : 1
PartNumber : SWT-316L16E14x18x2
ProductDescription : Instructions: Use DC+ (reverse polarity), however, an AC machine with sufficient open circuit voltage may be used. Bevel thick sections to a 60° Vee. Clean the weld zone of all contaminants. Preheating 300 series stainless steel is NOT required. The diameter of the electrode chosen should be equal to the thickness of the base metal. Use the lowest possible welding current or increase your welding speed in order to avoid overheating or distortion of the base metal. Overheating stainless steel can degrade the composition and corrosion resistant properties. The arc length should be kept as short as possible but do not touch the flux-coating of the electrode into the molten weld pool. Hold the electrode at a 15° angle into the direction of travel. Stringer beads should be used in the flat, horizontal, and overhead positions. The weaving technique should be used for vertical welding but not to exceed two to three times the diameter of the electrode. Remove all slag before making additional passes. On the final pass, allow the part to cool down partially before removing the slag, then promote rapid cooling by quenching with a wet rag or compressed air. This will preserve the corrosion resistant properties of the 300 series stainless. Do not allow to slow cool.
ProductSiteLaunchDate : 2023-07-06T21:44:25.005Z
Size : 1/8" - 2 Lb
UnitCount : 1
UnspscCode : 23271800