Cart 2 india

Specification
Brand : MAGNATE
BulletPoint : Fish Tail End, Solid Carbide, Right-Hand; 1/4" Shank Diameter; 2" Overall Length
BulletPoint1 : Diameter: 15 mm
BulletPoint2 : Total Length: 212 mm
BulletPoint3 : Length spiral 114 mm Morse cone (cm) 2
BulletPoint4 : Cut angled 118º spiral 20 - 30 ° angle, Tolerance H8, glossy finish, cut on the right side
BulletPoint5 : Cutting angle: 130 °, spiral angle: 20 - 30 °, Tolerancia: H8 Brown and Gold, layers, incision line on the right side;Applications: For Steel and steel die cast chrome and without Alear (with a maximum of approx. 900 N/mm², cast iron grey, malleable cast iron/steel with high alloys in chrome V2 a and V4 A, rust-free steel and these glasses are acids
Color : Schwarz
CuttingAngleString : 30.0 degrees
CutType : Carbide-Tipped Cut
ExternallyAssignedProductIdentifier1 : 0637881894611
ExternallyAssignedProductIdentifier2 : 637881894611
ExternallyAssignedProductIdentifier3 : 00008925056591
FinishType : Glossy
GpsrSafetyAttestation : 1
IncludedComponents : Twist drill
ItemDisplayDimensions_Height : 2.75 inches
ItemDisplayDimensions_Length : 0.3 inches
ItemDisplayDimensions_Width : 0.3 inches
ItemDisplayWeight : 0.25 pounds
ItemName : Magnate 9461 2 Flute Spiral Up-Cut Router Bit - 5.0mm Cutting Diameter, 3/4" Cutting Length
ItemPackageDimensions_Height : 21 centimeters
ItemPackageDimensions_Length : 2.5 centimeters
ItemPackageDimensions_Width : 2.5 centimeters
ItemPackageQuantity : 1
ItemShape : Rectangular
ItemTypeKeyword : spiral-router-bits
Manufacturer : Magnate
Material : Carbide
Material1 : Cobalt
Material2 : Alloy Steel
Material3 : Blend
Material4 : Blend
Material5 : Blend
MeasurementSystem : Inch
ModelNumber : 204150E
NumberOfFlutes : 2
NumberOfItems : 1
NumberOfPieces : 1
PackageLevel : unit
PartNumber : 9461
Pattern : Solid
ProductDescription : This 2-flute spiral bit is designed for solid wood and wood composites. While it can be used for certain plastic applications, O-flute and Z-flute bits are recommended. This bit works well in cutting Type I high density foam. A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed. Always refer to the operation manual of your router first, in the event that a router bit doesn't come with a speed chart, you may start at about 2,000 rpm slower than the maximum speed described in the chart below. Maximum speed below is for reference only, actual best performance speed varies depending on a number of factors i.e. size of the router bit, the material to be cut, etc. Run 24,000 rpm maximum for 1" overall diameter router bits; Run 20,000 rpm maximum for 1-1/2" overall diameter router bits; Run 18,000 rpm maximum for 2" overall diameter; Run 16,000 rpm maximum for 2-1/2" overall diameter router bits; Run 12,000 rpm maximum for 3" overall diameter router bits; Run 10,000 rpm maximum for 3-1/2" overall diameter router bits;
ProductSiteLaunchDate : 2013-04-14T06:53:13.396Z
Size : 15 mm
Style : Right
SupplierDeclaredDgHzRegulation : not_applicable
SurfaceRecommendation : Wood
UnitCount : 1
UnspscCode : 27110000