Cart 2 india

Specification
AgeRangeDescription : Adult
Brand : Jerry's Skating World
BulletPoint1 : Wrist Length Gloves w/ Scattered Crystals
BulletPoint2 : One Size Fits Most
BulletPoint3 : Jerry's 1107
BulletPoint4 : 85% Acrylic 15% Spandex
BulletPoint5 : Ice Skating Gloves
BulletPoint6 : From A&R Sports, the leading brand in sports accessories for over 20 years
CareInstructions : Hand Wash Only
Color : Tan
Color1 : White
Color2 : White
CustomerPackageType : Standard Packaging
Department : womens
EducationalObjective : Team Building Skills
ExternallyAssignedProductIdentifier1 : 654975800174
ExternallyAssignedProductIdentifier2 : 0654975800174
ExternallyAssignedProductIdentifier3 : 00765499104966
GpsrSafetyAttestation : 1
HandOrientation : Ambidextrous
ImportDesignation : Imported
IncludedComponents : 8 Inline Hockey Wheels
ItemDisplayDimensions_Height : 1 inches
ItemDisplayDimensions_Length : 12 inches
ItemDisplayDimensions_Width : 8 inches
ItemDisplayWeight : 0.25 pounds
ItemName : Jerry's Skating World Gloves 1107 (Tan)
ItemPackageDimensions_Height : 19 centimeters
ItemPackageDimensions_Length : 2.79 centimeters
ItemPackageDimensions_Width : 9.5 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : hockey-skate-accessories
Manufacturer : Gertens
Material : Spandex
Material1 : Wood
Material2 : Steel
ModelName : A&R Sports Blade Cover
ModelNumber : 0496
MountingType : sew-on
NumberOfPieces : 2
PartNumber : RINK
Pattern : Camouflage
ProductDescription : Instructions: 1) Have at least 5-6 inches of ice above your highest point. If it is too shallow, the ice will not freeze properly and then crack and bubble. 2) Using 2”x12”x10’ boards then connect them with brackets that a 2”x4” can fit in. Next, depending on the slope of the yard, cut plywood sheets and screw them into the frame (closing any gaps caused by sloping/uneven ground). Boards should be a minimum of 12" high (6" of water plus 6" of board to stop the puck). Then reinforce with triangle braces supporting any sloping area and, if needed, put a steel rod (rebar works great) through the brace for extra support. The key is making sure the boards will not slip or move when flooding. 3) Once the space is determined and the frame is built, measure and order ice rink poly. Allow 3-5 feet of extra ice rink poly for each side in order to make sure to have enough ice rink poly to easily go over the boards once the water is put in. 4) Typically, it is best to run 1 or 2 garden hoses into the rink. Depending on the size, this can take 10-30 hours. Once flooding has begun, monitor the rink to make sure the ice rink poly stays in place (making sure the wind does not blow your ice rink poly over the boards and back into the water). Alternative method: Some people believe that it is best to fill the ice rink in 1” intervals, allowing the ice to freeze in between layers. 5) Temperatures need to be consistently in the 20's or lower overnight. The rink will take about a week to freeze. If there is snow in the 48 hour forecast, don't start filling. If it snows, it will freeze and make the rink surface bumpy. 6) After about 5 days, put one foot on the rink and push down. If cracking is heard, then wait a couple more days and repeat. If no cracking, then begin to walk on it. If, while walking, cracking is heard, get off and try again in a few days. 7) For best results, resurface using a heated hose. Put a thin layer on when needed.
ProductSiteLaunchDate : 2017-06-13T07:00:00.000Z
Size : One Size
SoleMaterial : Polyurethane
SportType : skating
StreetDate : 2012-10-10T00:00:01Z
SupplierDeclaredDgHzRegulation : not_applicable
TargetAudienceKeyword : unisex
Theme : Sports
UnspscCode : 46181500
WarrantyDescription : 3 Month Warranty