Cart 2 india

Specification
Brand : AITRIP
BulletPoint1 : you will get 3pcs BME280 3.3V Pre-Soldered High Precision Altimeter Atmospheric Pressure, Temperature, and Humidity GY-BME280-3.3 Sensor Module
BulletPoint2 : BME280 is a precision sensor, is soldered onto PCB. It uses both I2C and SPI (supports 3-, 4-wire SPI) interface.
BulletPoint3 : Pressure: 300-1100 hPa; Temperature: -40 to +85°C ; Humidity: 0-100%
BulletPoint4 : BME280, the precision sensor from , is soldered onto PCB. Not only the pressure and the temperature, this sensor can measure humidity. It uses both I2C and SPI (supports 3-, 4-wire SPI) interface
BulletPoint5 : Interface: I2C (up to 3.4MHz), SPI (up to 10 MHz); Measures Pressure, Humidity, and Temperature with I2C and SPI Interfacing
Color : 3.3V
CompatibleDevices : Raspberry Pi models, Arduino models, microcontrollers with I2C or SPI capabilities
ConnectivityTechnology : I2C
ConnectivityTechnology1 : Wi-Fi
ConnectivityTechnology2 : Bluetooth
ConnectivityTechnology3 : USB
ConnectorType1 : Ethernet (RJ45)
ConnectorType2 : RS485 (screw terminal)
ExternallyAssignedProductIdentifier1 : 0687117725264
ExternallyAssignedProductIdentifier2 : 687117725264
IncludedComponents : GY-BME280 BME280 Digital 3.3V
ItemName : AITRIP 3PCS Pre-Soldered GY-BME280 BME280 Digital 3.3V Temperature Humidity Sensor Atmospheric Barometric Pressure Board IIC I2C Breakout Compatible with Arduino ，Raspberry Pi
ItemPackageDimensions_Height : 9.906 centimeters
ItemPackageDimensions_Length : 1.4986 centimeters
ItemPackageDimensions_Width : 6.1976 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : single-board-computers
Manufacturer : AITRIP
MemoryStorageCapacity : 8 MB
ModelName : GY-BME280
ModelNumber : RS485 TO ETH
NumberOfItems : 3
NumberOfPorts : 2
OperatingSystem : Linux
PartNumber : DA11892-1
PowerPlugType : type_b_3pin_na
ProcessorCount : 3
ProductDescription :

Specifications

Interface：I2C and SPI

Supply Voltage：3.3V

Measurements：Temperature, Pressure, Humidity. Pressure can be converted to altitude.

Compatibility：for Raspberry Pi and for Arduino Models, and any microcontroller with I2C or SPI capabilities.

Note： Soldering Comes Pre-Soldered.

Pins： 

VCC: This pin is used for Supply Voltage.

GND: This pin is used for ground.

SCL: This pin is used for the clock pulse for I2C communication.

SDA: This pin is used for transferring data through I2C communication.

CSB: This pin can be used to allow multiple devices to share the same I2C bus.

SDO: This pin can be used to select the device's I2C address when multiple BME280 sensors are connected to the same I2C bus.

Package Included:

3* Pre-Soldered BME280 3.3V Temperature Humidity Sensor Module

ProductSiteLaunchDate : 2023-08-22T07:40:26.747Z
Size : 3pcs N8R2
SupplierDeclaredDgHzRegulation : not_applicable
TotalUsbPorts : 2
UnspscCode : 43200000
WarrantyDescription : 1
WirelessCommStandard : bluetooth