SpecificationAspectRatio : 16:9
Brand : DORHEA
BulletPoint : Radioberry plastic casing. With cutouts to prevent excessive internal temperature and damage to the product
BulletPoint1 : The ESP32 CAM equips the ESP32 with everything necessary to program, run and develop on the wonderchip. Additionally, the board reserved the MPU6050,BME280 and an analog MIC.
BulletPoint2 : ESP32-CAM can be widely used in various IoT applications. It is suitable for home smart devices, industrial wireless control, wireless monitoring, QR wireless identification, wireless positioning system signals and other IoT applications. It is an ideal solution for IoT applications.
BulletPoint3 : ESP32 cam using low-power dual-core 32-bit CPU, can be used as an application processor, main frequency up to 240MHz, computing power up to 600 DMIPS, it can be used as a master mode to build an independent network controller, or as a slave to other host MCUs to add networking capabilities to existing devices.
BulletPoint4 : Note: Please make sure that the input power of the module is at least 5V 2A, otherwise the picture may have water lines; The ESP32 GPIO32 pin controls the camera power. When the camera is working, please pull GPIO32 low; Since IO0 is connected to the camera XCLK, please leave IO0 in the air when using it, and do not connect it to high or low level
BulletPoint5 : Better Heat Dissipation – The ICE Tower Cooler is made from 5mm copper tube and 28 aluminum fins and it also has a 40mm cooling fan. All are good for heat dissipation of Raspberry Pi Board.
BulletPoint6 : NOTE: The RGB lights on Fan and mood lights on OLED screen driver board will not light up unless installed driver, and OLED will not display any information until you have enabled it! Please read the manual carefully and follow the steps to enable it. Package Includes: 1 x ABS Mini Tower Case, 1x QC3.0 Power Supply, 2 x Acrylic Side Panel,1 x 0.96 Inch OLED Display (already mounted on the case), 1 x ICE Tower Cooler, 1x GPIO Edge Extention,1x Assembly Manual (Note: Raspberry Pi 4B is Not included in the package)
Color : 4 Set
CompatibleDevices : OV2640 Camera, OV7670 Camera, WiFi-enabled devices, Bluetooth-enabled devices
ConnectivityTechnology : USB
ConnectivityTechnology1 : GPIO
ConnectivityTechnology2 : I2C
ConnectivityTechnology3 : Wi-Fi
CoolerHeatsinkCompatibility : Raspberry Pi 5
CoolingMethod : forced air
ExternallyAssignedProductIdentifier1 : 701715461116
ExternallyAssignedProductIdentifier2 : 0701715461116
GpsrSafetyAttestation : 1
GraphicsCardInterface : integrated
GraphicsDescription : Integrated
HumanInterfaceInput : buttons
IncludedComponents : Comimark 5Pcs Digispark Kickstarter ATTINY85 for Arduino General Micro USB Development Board
ItemName : 4PCS ESP32-CAM Camera Module ESP32 CAM WiFi Bluetooth Development Board ESP32 Wireless OV2640 Camera Module with Jumper Wire
ItemPackageDimensions_Height : 14.4 centimeters
ItemPackageDimensions_Length : 3.8 centimeters
ItemPackageDimensions_Width : 10.6 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : single-board-computers
KeyboardLayout : qwerty
Manufacturer : DORHEA
Material : Plastic
Material1 : Acrylic
Material2 : Aluminum
MemoryStorageCapacity : 8 KB
ModelName : ESP32 CAM
ModelNumber : 13631-1
ModelYear : 2021
MountingType : Panel Mount
NativeResolution : 212x104
NumberOfBoxes : 1
NumberOfDisplaysSupported : 1
NumberOfItems : 1
OperatingSystem : FreeRTOS
PartNumber : 13631-1
PersonalComputerDesignType : barebone
PowerConnectorType : 2-Pin
PowerConsumption : 26.4 milliwatts
ProcessorCount : 2
ProductDescription : ESP32 CAM WiFi Bluetooth Module:
Ultra-small 802.11b/g/n Wi-Fi BT/BLE SoC module
Low-power dual-core 32-bit CPU for application processors
Up to 240MHz, up to 600 DMIPS
Built-in 520 KB SRAM, external 4M PSRAM
Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
Support OV2640 and OV7670 cameras with built-in flash
Support for images WiFI upload
Support TF card
Support multiple sleep modes
Embedded Lwip and FreeRTOS
Support STA/AP/STA AP working mode
Support Smart Config/AirKiss One-click distribution network
Support for serial local upgrade and remote firmware upgrade (FOTA)
Support secondary development
Note:
1.Please ensure that the module input power is at least 5V 2A, otherwise the image will unstable.
2.ESP32 GPIO32 pin controls camera power. When the camera is working, please pull GPIO32 low.
3.Since IO0 is connected to the camera XCLK, please leave IO0 floating when using it. Do not connect high and low level.
4.The factory has the default firmware, no additional download is available. Please handle it carefully if you need to re-burn other firmware.
Package include:
4 x ESP32-CAM Module
1 x 20cm 10pin Female-Female Jumper Wires
1 x 20cm 10pin Female-Male Jumper Wires
ProductSiteLaunchDate : 2020-12-24T06:06:42.297Z
Resolution : 212 x 104
Size : 4 Set
SpecificationMet : SPI
SpecificUsesForProduct : Industrial, Lab/Instrument, Embedded Systems
Style : Minimalist
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
SystemRamType : sdram
TotalUsbPorts : 4
UnitCount : 1
UnspscCode : 46171600
Voltage : 5 volts
WarrantyDescription : 1 year
Wattage : 125 watts
WirelessCommStandard : 802_11_B
WirelessCommStandard1 : 802_11_B
WirelessCommStandard2 : bluetooth
WirelessNetworkTechnology : wifi