Cart 2 india

Specification
AudioOutputMode : Stereo
Brand : Kramer
BulletPoint : DOUBLE UCP BLANK PNL
BulletPoint1 : Simple and Powerful Maestro 1. 0 Room Automation
BulletPoint2 : Max. Data Rate — 10. 2Gbps (3. 4Gbps per graphic channel), Resolution Support up to 4K@60Hz (4: 2: 0)
BulletPoint3 : Control — Ethernet and embedded Web pages over RS–232
BulletPoint4 : Automatic Live Input Detection, Automatic Input Selection
BulletPoint5 : Range — Up to 100m in normal mode
CircuitType : 2-way
CompatibleDevices : Laptop
CompatibleDevices1 : Speaker
CompatibleDevices2 : Smartphone
ConnectivityTechnology1 : HDMI
ConnectivityTechnology2 : Ethernet
ConnectorType : Wire
ConnectorType1 : VGA
ConnectorType2 : HDMI
ControlMethod : remote
ExternallyAssignedProductIdentifier : 7291063075842
ExternallyAssignedProductIdentifier1 : 656747022906
ExternallyAssignedProductIdentifier2 : 0656747022906
ItemDisplayDimensions_Height : 10.19 inches
ItemDisplayDimensions_Width : 3.49 inches
ItemName : Kramer WP-20(B) HDMI/XGA/Ethernet/RS-232/Stereo HDBaseT WP Extender (Transmitter)/Black
ItemPackageDimensions_Height : 1 inches
ItemPackageDimensions_Length : 1 inches
ItemPackageDimensions_Width : 1 inches
ItemPackageQuantity : 1
ItemTypeKeyword : audio-video-selectors
Manufacturer : Kramer
Material : Plastic
ModelNumber : KDS-DEC3
MountingType : Wall Mount
NumberOfBoxes : 1
NumberOfItems : 1
NumberOfPositions : 2
OperationMode : manual
OutputWattage : 43
PartNumber : WP-20(B)
ProductDescription : Frequency Response (Hz, +/-3dB) 35-20,000 The Jamo AT-1A Volume control can be used as a volume control for one pair of speakers. PLACEMENT The AT-1A should not be located close to light switches/dimmers as this may cause a hum in the speakers. If the AT-1A is located close to these devices it must be mounted in a separatly grounded electrical box. Speaker cables/wires should also be as far away from electrical wires as possible. INSTALLATION The amplifier must be turned OFF before you install the AT-1A and/ or speakers or it may cause damage to the amplifier. Connect the speaker output on the receiver/amplifier to the INPUT on the AT-1A. Connect the OUTPUT from the AT-1A to the left and right speakers When connecting speaker cables/wires from the amplifier to the AT-1A and from the AT-1A to the speakers make sure LEFT (L) is connected to LEFT (L), RIGHT (R) to RIGHT (R), POSITIVE (+) to POSITIVE (+) and NEGATIVE (-) to NEGATIVE (-). If terminals are colour coded, RED is POSITIVE (+) and BLACK is NEGATIVE (-). SET-UP Before turning on the amplifier turn the amplifier volume to minimum. Turn the AT-1A to maximum volume (clockwise). Turn the amplifier on and slowly turn up the volume to the highest desired level without distortion from the speakers. The volume of the speakers are now controlled by the AT-1A and the amplifier volume control should not be used.
ProductSiteLaunchDate : 2018-03-19T00:00:00.000-07:00
StreetDate : 2020-02-04T00:00:01Z
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
SupportedInternetServices : YouTube
SurroundSoundChannelConfiguration : 2.0
SwitchType : Rotary
TerminalType : Screw
TotalHdmiPorts : 1
UnitCount : 1
UnspscCode : 25174400
VideoEncoding : Stereo
WarrantyDescription : na