Cart 2 india

Specification
AgeRangeDescription : Adult
Athlete : women's lingerie camisoles & tanks
BottomStyle : Skirted
Brand : 3M
BulletPoint1 : Use wet with water or dry for sanding old finishes, fine featheredging and surface sanding
BulletPoint2 : 3M wetordry stays flexible and cuts fast
BulletPoint3 : With patented technology SpreadCycle High Chopper frequency, dcStep, stallGuard2 stall detection technology, CoolStep Stream Dynamic Adjustment technology, can save 70% energy, StealthChop Mute technology.
BulletPoint4 : Compared to the TMC2100 stepper motor driver module, TMC2208 driver module is with lower heat. The heat of TMC2208 in 0.8A with the equivalent effect of the TMC2100 heat in 0.5A , can be used interchangeably with the TMC2100.
BulletPoint5 : Support UART Mode You Can use UART Mode in MKS SGEN L V1.0 / MKS GEN L V2.0 / MKS Robin E3D, SKR 1.3 / 1.4 by setting jumper cap. (No jumper is needed, no welding drive is required, and it is more convenient to use) This function does not support MKS GEN L V1.0
CareInstructions : Hand Wash Only
Collection : All
Color : Blue
Department : womens
ExternallyAssignedProductIdentifier1 : 051144020027
ExternallyAssignedProductIdentifier2 : 0051144020027
ExternallyAssignedProductIdentifier3 : 50051144020022
FabricType : 100% Polyester
FitType : Loose Fit
ImportDesignation : Imported
IncludedComponents : ...
ItemName : 3M Wetordry Abrasive Sheet 413Q, 02002, 9 in x 11 in, 400A, 50 Sheets Per Box
ItemPackageDimensions_Height : 28.8 centimeters
ItemPackageDimensions_Length : 1.3 centimeters
ItemPackageDimensions_Width : 23.8 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : sandpaper-sheets
LeagueName : MLB
Manufacturer : 3M
Material : Silicon Carbide
Material1 : Silk
Material2 : Cotton
ModelName : ...
ModelNumber : 400A-case
NumberOfItems : 50
PartNumber : 051144020027
Pattern : Floral
Pattern1 : Floral
Pattern2 : Plaid
ProductDescription : Parameter:

Default current:1.25a
Max current:2.0a
Logic voltage:3.3v/5v
Input voltage:4.75v-36v
Microstep:up to 1/256
Mode:dir/step,uart

1.Measuring:
The driving current must be converted by measuring the driving voltage. To measure the driving voltage Vref, refer to the voltage between the knob on the drive and the metal casing (gnd) of the USB interface as Vref. The drive current can be converted by Vref using a different drive conversion formula.

2.Adjustment:
Vref can be adjusted according to the running condition of the motor. By adjusting the knob above (clockwise is increased, counterclockwise is reduced)

3.Note:
Before adjusting the knob, it must be done with the power off. After the adjustment is completed, the power-on measurement is taken to prevent the drive or the motherboard from burning out.
Drive current algorithm and regulation
1. Vref measures the voltage of Gnd and the middle end of the potentiometer.
2. Do not connect the motor when measuring voltage, otherwise it will easily burn the drive.
3. Turn on the power when measuring voltage. Do not connect USB power only. Please pay special attention to the direction, do not insert it!

4.Attention:
1)Don't plug or unplug and wire or module when power is on.
2)Don't even touch the board when power is on or your hand has static charge (you can move static charge by touching metal tap).
3)Reversing +/- or otherwise incorrectly connecting the power supply or fan, hot bed, or even the 5v output on the motherboard can damage your electronic equipment and cause a fire hazard.
4)Incorrectly inserting stepper drivers will destroy your electronics and cause a fire risk .Always make sure to insert drivers in correct orientation and in the socket correctly .Before inserting the driver, first check whether the signal of the drive pin corresponds to the signal on the moth
ProductSiteLaunchDate : 2008-02-04T12:49:44-00:00
Size : 9 in x 11 in
SpecialSizeType : petite
StrapType : Spaghetti
StreetDate : 2017-12-12T00:00:01Z
Style : TMC2208
SupplierDeclaredDgHzRegulation : not_applicable
TeamName : Tennis
Theme : Western
UnitCount : 50