Cart 2 india

Specification
Brand : INTSUPERMAI
BulletPoint : Vacuum degree is the most important process parameter for rotary evaporators, and users often encounter the problem of insufficient vacuum degree, which is often related to the properties of the solvents used. In industries such as biochemical pharmaceuticals, water, ethanol, acetic acid, ethyl ether, petroleum ether, chloroform, toluene, etc. are often used as solvents. However, general vacuum pumps cannot withstand strong organic solvents, and special corrosion-resistant vacuum pumps can be selected. (We recommend using a water circulation vacuum pump, which is available in our company).
BulletPoint1 : Product Parameters: Heating Power:400W, The Number of Holes:36, The Diameter of Each Hole:0.63"(16mm),Gas Needle Length:5.9"(15cm), Temperature Range:Room Temperature 5℃-150℃, Timing Time:A maximum of 99 hours 59 minutes, Control Accuracy:≤±0.5℃, Display Precision:±0.1℃, Maximum Gas Pressure: 0.02Mpa
BulletPoint2 : Controlled Independently: Each of the 36 nitrogen valve switches can be controlled individually, and each needle can blow nitrogen separately for safety and no waste of gas.The position of gas needle in air cavity can be adjusted to suit for different types of tubes
BulletPoint3 : Rapid concentration: Synchronously working with heating by dry bath in the bottom and nitrogen blowing on the surface accelerates liquid evaporation and sample concentration
BulletPoint4 : LED Display: LED display immediate temperature and diminishing time. Operation is simple and convenient
BulletPoint5 : High Quality Built in overheat protection, automatic fault detection and fault beep alarm devices
Color : Gold Color
ExternallyAssignedProductIdentifier1 : 0840403757145
ExternallyAssignedProductIdentifier2 : 840403757145
IncludedComponents : host
ItemName : INTSUPERMAI 36 Holes Sample Concentrator Nitrogen Evaporator Lab Sample Blowing Ambient Concentrator Dry Heated Blower Nitrogen 110V
ItemPackageDimensions_Height : 11 inches
ItemPackageDimensions_Length : 17 inches
ItemPackageDimensions_Width : 16 inches
ItemPackageQuantity : 1
ItemTypeKeyword : science-lab-rotary-evaporators
Manufacturer : INTSUPERMAI
Material : glass
ModelName : WBTYgud52q6afe-13
ModelNumber : px201
NumberOfBoxes : 1
NumberOfItems : 1
PartNumber : S056591
ProductDescription : Working principle: the nitrogen into the heated surface of the sample and make the solvent t evaporate and separated rapidly, thereby reaching the sample enrichment purpose without oxygen, keep the sample purer. Nitrogen concentrator instrument can concentrated dozens of samples simultaneously, saving time and high efficient, instead of rotary evaporation instrument.
Product Parameters
Voltage: AC110V 60Hz
Heating Power: 400W
The Number of Holes: 36
The Diameter of Each Hole: 0.63"(16mm)
Gas Needle Length: 5.9"(15cm)
Temperature Range: Room Temperature 5℃-150℃
Timing Time: A maximum of 99 hours 59 minutes
Control Accuracy: ≤±0.5℃
Display Precision: ±0.1℃
Maximum Gas Pressure: 0.02Mpa
Package Size: 16.5"*16"*10.6"(43cm*41cm*26cm)
Net Weight/Gross Weight: 16LB(6.95kg)/18LB(8.05kg)
Note: if you need other numbers of holes, please contact us.
Paackage Included: Termovap Sample Concentrator ×1, The Power Cord ×1, Nitrogen Connection Pipe ×1, Fuse ×3
ProductDescription1 : I. Purpose and Features The rotary evaporator is mainly used for concentration, crystallization, drying, separation and solvent recovery in the pharmaceutical, chemical and biopharmaceutical industries. Its principle is to heat at a constant temperature under vacuum conditions, causing the rotating bottle to rotate at a constant speed, forming a large area of film on the bottle wall for efficient evaporation. The solvent vapor is cooled by an efficient glass condenser and collected in a collection bottle, greatly improving evaporation efficiency. It is particularly suitable for the concentration and purification of biological products that are prone to decomposition and denaturation at high temperatures. The company's rotary evaporator combines the essence of similar domestic products and the company's successful experience, and has formed a series of 2L, 3L, 5L, 10L, 20L, 50L, with product design following the principles of efficiency, practicality, and economy. All for the sake of users. Characteristics of RE201D rotary evaporator 1. The use of PTFE and fluorine rubber composite seals can maintain a high degree of vacuum. 2. Adopt high-efficiency condenser to ensure high recovery rate. 3. Continuous feeding is possible. 4. Digital thermostatic control of the water bath pot. Lifting of the hand wheel of the water bath pot 5. Reasonable structure, careful materials, stainless steel and aluminum alloy parts are widely used in mechanical structure, and high temperature and high boron glass is used for all glass parts. The key components of the electrical appliances are imported. The fluorine rubber seal has been fully adopted in the new national standard, which is convenient for users to purchase and replace.
ProductDescription2 : II. Main Technical Parameters Rotating bottle capacity: 500-2000ml Capacity of collection bottle: 500-1000ml Rotating speed: 10-120 rpm (AC stepless speed regulation) Motor power: 40W Water bath pot power: 1.5KW Power supply voltage: 220V50Hz/60Hz±10% III. Instrument installation The rotary evaporator consists of three main parts: mechanical parts, glass parts, and a thermostatic water bath. The large module is packaged in a box when it leaves the factory, making installation very convenient. The specific procedure is as follows: 1. Install the pressure gauge rod on the stainless steel pole and tighten it. 2. Remove one nut at the lower end of the stainless steel frame, tighten the other nut on the stand, and thread it into the stainless steel base plate. Then tighten the nut with the removed nut, and make sure that the front of the pressure gauge faces the installer. 3. Place the rack steadily on the workbench. If it is uneven, adjust the screws inside the four hard rubber feet under the base plate. 4. Move the center of the head to a height of 48cm from the chassis, tilt it to the right by about 25 degrees, and lock the various locking screws on the frame. 5. Fix the electric control box according to the drawing and plug in the five-pin plug of the motor. 6. Fix the flange end of the four-way bottle on the head of the machine, and make the upper and lower ports of the four-way bottle vertical. 7. Insert the condenser into the upper opening of the four-way bottle, adjust the movable joints to make the condenser vertical, and use a fixing clip to hold it. The pipe joints of the condenser should be backward. 8. Insert the feeding switch into the four-way bottle, connect the collection bottle to the lower opening of the four-way bottle, secure it with a bottle clamp, and attach the rotating bottle to the right end of the rotating shaft, securing it with a bottle clamp. 9. Place the water bath pot under the rotating bottle and add clean water to 2/3 of the pot (tap water should be left for 1-2 days). 10. Connect the vacuum tube connector at the exhaust tube with a vacuum tube, and connect the other connector to the vacuum pump or laboratory vacuum switch. Precautions: (1) All glass pieces should be cleaned before installation. (2) Apply a small amount of vacuum grease to each standard port and sealing surface to increase air tightness. (3) After installation, the head position should be locked and cannot be moved.
ProductDescription3 : IV. Usage The speed of the rotary evaporator depends on three factors: The higher the vacuum degree, the faster the speed. The vacuum degree should not be less than 0.096 MPa when water evaporates. 2. The higher the temperature of the water bath, the faster the speed. Generally, it should not exceed 80℃, and the specific requirements should be followed according to the process requirements. 3. The lower the cooling water temperature, the faster the speed, and the better the effect of using refrigerated water. Second, main technical parameters Rotating bottle capacity: 500-2000ml Capacity of collecting bottle: 500-1000ml Rotating speed: 10-120 rpm (AC stepless speed regulation) Motor power: 40W Water bath pot power: 1.5KW Power supply voltage: 220V50Hz/60Hz±10% III. Instrument installation The rotary evaporator consists of three main parts: mechanical parts, glass parts, and a thermostatic water bath. The large module is packaged in a box when it leaves the factory, making installation very convenient. The specific procedure is as follows: 1. Install the pressure gauge rod on the stainless steel pole and tighten it. 2. Remove one nut at the lower end of the stainless steel frame, tighten the other nut on the stand, and thread it into the stainless steel base plate. Then tighten the nut with the removed nut, and make sure that the front of the pressure gauge faces the installer. 3. Place the rack steadily on the workbench. If it is uneven, adjust the screws inside the four hard rubber feet under the base plate. 4. Move the center of the head to a height of 48cm from the chassis, tilt it to the right by about 25 degrees, and lock the locking screws on the frame.
ProductSiteLaunchDate : 2024-09-11T08:47:25.529Z
Size : 5.5mm
Style : Without ETL Certified to UL and CSA
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
UnitCount : 1
UnspscCode : 41000000
Voltage : 110 volts