Cart 2 india

Specification
Brand : Dlinanta
BulletPoint1 : [Super Fast Knoting] The operation of the automatic rebar tier is quite easy. It only takes 0.8s to finishing a knot, saving you a lot of time and effort. The rechargeable battery takes only 1.5 hours to fill and can be used for 1500 Times
BulletPoint2 : [8-34mm Application Range] This reba tie tool can easily knot rebar with a total diameter of 8 to 34mm and knot wire length of 300 to 500mm.
BulletPoint3 : [Easy to Use] This Tier Tying Machine is small, light in weight, easy to grasp, 3–5 times less labor-intensive than manual labor, very convenient for your use
BulletPoint4 : [Spcs] Voltage: 12v, Battery: Lithium-ion Batteries, Battery Capacity: 4500 Mah, Battery Charging Time: Hours Full Filling, Tying Wire Diameter: 0.8mm, Tying Wire Length: More than 110 M, Applicable Scope of Steel Strapping: 8mm - 34mm, Knot Wire Length: 300 - 500mm, Knot Number per Charge: 1500 Times, Knot the Required Time: 0.8 Seconds at a Time
BulletPoint5 : [Wide Application Areas]Used in the construction market, including civil buildings, ground pipes, floor heating floor meshes, steel bars, etc
Color : Orange
ExternallyAssignedProductIdentifier1 : 0749767444725
ExternallyAssignedProductIdentifier2 : 749767444725
IncludedComponents : 1x Tying Machine, 1x Pliers, 1x Charger, 1x Storage Box, 2x Lithium Ion Batteries, 1x Tying Wire in the Machine (Tying WireStandard: About 0.8 Mm X 110 M/Roll)
ItemName : Rebar Tying Machine, 8mm-34mm Tier Tying Machine Rechargeable 12V Automatic Rebar Tier Tying Machine Electric Reinforcing Rebar Tier Gun for Building Market
ItemTypeKeyword : rebar-cutters-and-benders
Manufacturer : Dlinanta
Material : Plastic + Metal
ModelName : Rebar Tying Machine
ModelNumber : GDSE3R
PowerSourceType : dc
ProductDescription :

Specifications：

Color: Orange

Material: Plastic + Metal

Voltage: 12v

Battery: Lithium Ion Batteries

Battery Capacity: 4500 Mah

Battery Charging Time: 1.5 Hours FullFilling

Tying Wire Diameter: 0.8mm

Tying Wire Length: More than 110 M

Applicable Scope of Steel Strapping: 8mm -34mm

Knot Wire Length: 300 - 500mm

Knot Number per Charge: 1500 Times

Knot the Required Time: 0.8 Seconds at aTime

Machine Size: 275 Mm * 65 Mm * 240 Mm / 10.83''X2.56''X9.45''(Appr.)

Tool Box Size: 42cm (16.54inch) *30cm(11.81inch) *10cm (3.94inch)

Tying Wire Installations：

 

1. in the State of Start-up, Press theLocking Plate of the Opening Wire Plate, Open the Plate Cover.

 

2. Take out the Tying Wire, Tear thePackaging Film, Pull Straight Wire Head About 10 Cm, Load into the BindingMachine in the Clockwise Direction, the Wire Head into the Guide Tap Tube.

 

Note: Clench the Wire Plate When Tear thePackaging Film, Do Not Let the Wire Loose. If the Wire Is Free to Disperse, ItWill Lead to the Spread of the Wire Stuck in the Wire Plate.

 

3. Insert the Head of the Wire Guide intothe Tap Pipe Until It Is Resisted.

 

4. Cover the Plate and Fasten the LockingPiece.

 

5. Pinch the Wire Forward with Two Fingers,Press and Hold the Switch and Send the Wire out.

 

6. If You Want to Take out the Wire PlateWhen Finished, Press and Hold the Locking Piece, Open the Wire Plate CoverPlate, Holding the Wire Tray to the Side and Pull out.

 

Operation Instructions：

1. the Rebar Tirer's Jaws Are Stuck to theIntersection of the Steel Bars, and the Steel Bars Are Hooked at 45 DegreeAngles.

Note: There Can Be No Barrier Between theMouth of the Jaws and the Wire.

2. Press the Start Switch, the Rebar TirerMachine Carries on the Work (Spins, Hinges Tightly, Cuts off)

Note: Press One Button at a Time, Do NotProbe the Jaws at Work.

3. When Automatic Completion, the Jaw fromthe Steel bar Intersection and Then Pull Back, Complete the Process and Preparefor the Next Binding.

4. When the Binding Process Is NotCompleted, Do Not Unplug the Machine in Advance, Otherwise It Will Cause theBundling of the Goods Tied Skidding.

Operating Skills：

 1. in Use, the Left Tilt 45 Degrees AfterBanding, the Next Time the Banding into a Right Tilt 45 Degrees Banding, Leftand Right Alternately Banding.

2. When the Machine Is About to Tighten,the Machine Will Appear Slightly Shaking, While Holding the Hand of the MachineNot Too Tight, You Can Relax Properly.

 

Maintenance：

1. Clean the Machine Regularly, Keep theWire Mouth Clean.

2. This Product Can Not Be Placed Randomly,so As Not to Cause Damage to Parts.

3. Batteries Must Not Be Placed Togetherwith Other Metal Objects to Avoid Short Circuit.

4. Non-professional Do Not Disassemble theMachine Arbitrarily, Lest Cause Damage.

5. When You Encounter an UnresolvedFailure, Please Give It to the Professional Repair.

Package Included:

1x Tying Machine

1x Pliers

1x Charger

1x Storage Box

2x Lithium Ion Batteries

1x Tying Wire in the Machine (Tying WireStandard: About 0.8 Mm X 110 M/Roll)

ProductSiteLaunchDate : 2024-05-09T08:20:07.921Z
SupplierDeclaredDgHzRegulation : not_applicable
UnitCount : 1