Specification Brand : IVLPHA BulletPoint1 : Quick installation, simple and flexible, space-saving. Even after installation, the direction of tubing can be changed freely. BulletPoint2 : The release ring adopts the ellipse design to make it more convenient and labor-saving for disconnection. Stainless steel locking claw, never stuck, never rust. BulletPoint3 : All taper threads are pre-coated with Teflon with fine seal performance. (It may needs extra Teflon tape when thread of equipment damaged before) BulletPoint4 : Fit for icemaker, refrigerator, cold water filter, etc. Please do not apply for the tube joint with additional external load (bending, twist or pulling, e.g.: Trailer, Air Suspension). BulletPoint5 : Pressure Range: 0~1.1Mpa(0-160psi), Negative Pressure: -100Kpa (-29.5 in.Hg), Pressure Proof Test: 3.0Mpa (435psi), Temperature Range: 0~60℃ (32~140℉), Applicable Tube: Nylon,Polyamide (PA) / Polyurethane (PU). Applicable Fluid: Air, Vacuum, Water. Color : White ConnectorType : Elbow CustomerPackageType : Standard Packaging ExteriorFinish : Brass ExteriorFinish1 : White ExteriorFinish2 : PVC ExternallyAssignedProductIdentifier1 : 665626125584 ExternallyAssignedProductIdentifier2 : 0665626125584 ExternallyAssignedProductIdentifier3 : 00665626125584 GpsrSafetyAttestation : 1 IncludedComponents : 1 Fitting ItemDisplayWeight : 0.02 pounds ItemName : IVLPHA Push to Connect Fitting 1/4" Tube OD x 10-32 UNF Male Thread, Pneumatic Male Elbow Air Water Line 90 Deg Swivel Elbow Quick Push in Connectors (Pack of 5) ItemPackageDimensions_Height : 12.2936 centimeters ItemPackageDimensions_Length : 1.6002 centimeters ItemPackageDimensions_Width : 7.5946 centimeters ItemPackageQuantity : 1 ItemShape : 90 Degree Elbow ItemTypeKeyword : push-to-connect-tube-fittings Manufacturer : IVLPHA Material : Polybutylene Terephtalate (PBT) and Nickel Plated Brass Material1 : Plastic Material2 : Polypropylene ModelName : L ModelNumber : 04U10 NumberOfItems : 5 NumberOfPieces : 5 PackageLevel : unit PartNumber : L04U10 ProductDescription : Before use, it should make clear following points
Warning
a) Except air and water (only special type and custom-design, e.g.: icemaker, refrigerator, cold water filter), never attempt to use the tube joint other fluids. b) The tube joint application is prohibited where spark and fire might be occurred. c) The tube joint application is prohibited if water temperature is above 60℃ (140℉) because resin might be decomposed and damaged in water under a high temperature. d) The tube joint is not designed for application where there is static charge. e) Never apply tube joint with additional external load (bending, twist or pulling, e.g.: Trailer, Air Suspension),
Cautions
1) If you use other supplier tubing, the different tubing tolerance might case leakage or incorrect connection and disassembly. It must check if tubing OD is measured by Metric Size or Inch Size.
2) Always check the end of tubing for a right angle cutting and check the external surface of tubing for any damage or scratch. Please refer to following instruction in connection of tubing. When you insert the air tubing into the joint, you will have two-step feeling. Section One is locking claw while Section Two is sealing ring. You must insert the tube into Section Two.
Sleeve is used in tubing connection and disconnection. The sleeve is designed as an oval shape, which is convenient in assembly and disassembly. After connection of tube joint and tubing, always try to pull tubing and ensure its firm connection.
3) Cautions during disassembly of tubing before disconnection of tubing, always check tubing internal pressure for zero.
For disconnection of tubing, always press sleeve heavily and then pull out tubing. If sleeve is net pressed with enough force, it is hard to pull out tubing and external surface scratch might be resulted by locking claw, which is the cause of air leakage.