Cart 2 india

Specification
Brand : Generic
BulletPoint : MTD4-U10
BulletPoint1 : 1-Food-Grade Quality meets NSF Standard Material: This RO fittings are produced with food-grade non-toxic material,which is complied with requirments for materials in contact with food and drinking water
BulletPoint2 : 2-Technical Specifications: Tube Connector for connecting plastic or copper 1/4" O.D. tube to 1/4" female NPT in pipes or fittings; Body: food-grade POM; O-ring:NBR; Collet: POM+STS301; Working Pressure and temperature Range: Maximum 150 psi @ 70°F (10.3 bar @ 21°C) / 60 psi @ 140°F (4.1 bar @ 60°C); Minimum 33°F (1°C)
BulletPoint3 : 3-Various Applications: Push fit Connectors are designed for water,food and air contact but can be used with selected gases, vacuum & liquids; like Reverse Osmosis Systems, Driking water filtration systems, Water coolers, Coffee Machines, RVs, Misting Systems, Beverage Dispensers, Ice Makers and pneumatic systems etc
BulletPoint4 : 4-Easy Installation and Testing:Quick connect without tools required to provide permanent or removable leak-proof connections with RO filter; Pushing and pulling on the connection points and be prssure-tested prior putting quick fitting into service. Plumbing connectors should not be exposed to excessive side loads and caution should be taken to prevent undue stress and excessive side loading
BulletPoint5 : 5-Our ISO9001 registered quality system ensures our customers a superior level of product quality. Defects are easily detectable and maintenace is easy with its easy dismantling for access. Clip-Free Technology makes zero-leak connection without extra parts needed.
Color : Black,Copper
ConnectorType : Flange
ConnectorType1 : Cap
ConnectorType2 : Elbow
ExteriorFinish : Copper
ExteriorFinish1 : Nickel
ExteriorFinish2 : Brass
ExternallyAssignedProductIdentifier1 : 0631060923369
ExternallyAssignedProductIdentifier2 : 631060923369
IncludedComponents : 12PCS Push Into Gas Connector
ItemName : EZRODI 1813-A 1/4'' Male NPT to 1/4'' Push to Connect Fittings with Black O'ring for RO Water filter System(Pack of 10), Copper
ItemPackageDimensions_Height : 0.8 inches
ItemPackageDimensions_Length : 6 inches
ItemPackageDimensions_Width : 4 inches
ItemPackageQuantity : 4
ItemTypeKeyword : push-to-connect-tube-fittings
Manufacturer : EZRODI
Material : Copper
Material1 : Stainless Steel
Material2 : Nbr
ModelName : QS30821
ModelNumber : QS30821
NumberOfItems : 10
NumberOfPieces : 10
PartNumber : QS30821
ProductDescription : Material Characteristics for Portable Water Applications

Push-Fit Fittings are suitable for portable water applications with a maximum chlorine concentrate of 4 ppm, For cold water applications only
*POM: Highly durable and resistant to fatigue and creep; It has high resistance to a wide range of organic& inorganic chemicals and detergents. Not recommended for use with strong acids or repeated exposure to strong oxidize. Direct exposure to sunlight will reduce fittings’ service life and may lead to failure;All fittings and tubing should not be used near heart emitting appliances
*STTeeth:STS301 Stainless Steel, It has good corrosion resistance , heat resistance, low temperature strength and mechanical properties, and durable.
*NBR: Good Oil resistance, high wear resistance, good heat resistance, strong adhesion

Installation Instructions

*Step 1-Cut the Tubing
Cut the Water Line cleanly and squarely, ensure that the RO Tubing has a smooth outside diameter without any burrs, chamfers or score marks prior to inserting it into the RO fitting. Tubing that has not been cut properly can cause drips and leaks.
*Step 2-Insert the Tubing
Push the RODI tubing through the collet and O-rings until it bottoms out against the tube stop. The collet holds the tube in place and the o-ring provides a leak resistant seal, if you need to remove the tubing always re-cut before connection tubing again. Scores on tubing can cause failure.
*Step 3-Inspect and Test
Push and pull the tubing toward and away from the fitting to ensure that it has been installed properly. Test and inspect the installation for any leaks.
*Step 4-Tube Removal
Relieve pressure from the tubing and fitting. Push the collet flange against the fitting body while pulling the tubing away from the fitting to release it.
ProductSiteLaunchDate : 2021-11-08T07:45:43.576Z
Size : 1/4" tube to 1/4" NPT (M)
StreetDate : 2017-03-12T00:00:01Z
Style : Push to Connect
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
UnitCount : 3.52
UnspscCode : 40141700