Cart 2 india

Specification
Brand : PRO-EDGE INDUSTRIAL PNEUMATICS AND CONTROLS
BulletPoint1 : 3/8" Tube O.D. x 3/8" MNPT Fixed Male Branch Tee
BulletPoint2 : Heavy Duty All Brass Construction, Full Flow Design
BulletPoint3 : 0-150 PSI Working Pressure Range of the Fitting. Please reference the working / burst pressure of the tubing type you plan on connecting to this fitting for the most accurate Maximum PSI rating.
BulletPoint4 : Working Temperature Range of -10° - 200° F, Full Flow Design, Self Contained Assembly, Reusable
BulletPoint5 : Please Note 3/8" NPT Measures 0.675" Outside thread diameter in inches. See attached NPT Thread chart.
Color : Brass
ConnectorType : Tee
ConnectorType1 : Cap
ConnectorType2 : Elbow
ExteriorFinish : Brass
ExteriorFinish1 : Nickel
ExteriorFinish2 : Brass
ExternallyAssignedProductIdentifier1 : 743270106828
ExternallyAssignedProductIdentifier2 : 0743270106828
ExternallyAssignedProductIdentifier3 : 00743270106828
ItemName : 3/8" Tube O.D. x 3/8" MNPT Heavy Duty Brass Push-In Branch Tee, Splitter For Air Line, Pneumatic Fitting (1)
ItemPackageDimensions_Height : 7.0104 centimeters
ItemPackageDimensions_Length : 2.0066 centimeters
ItemPackageDimensions_Width : 5.4102 centimeters
ItemPackageQuantity : 10
ItemShape : Tee
ItemTypeKeyword : push-to-connect-tube-fittings
Manufacturer : PRO-EDGE INDUSTRIAL PNEUMATICS AND CONTROLS
Material : Brass
Material1 : Plastic
Material2 : Metal
ModelName : Fixed Male Branch Tee
ModelNumber : PLDV-119
NationalStockNumber : 4730-01-559-8929
NumberOfItems : 1
NumberOfPieces : 1
PartNumber : PLDV-119
ProductDescription : Pro-Edge Industrial push-in fittings, also known as Push-to-pull, push-to-connect, push-fit, or instant fittings, let you easily connect hoses in your compressed air system. These self contained fittings are a type of easily removed fittings that allow an air line to be attached. Simply push tubing in, no tools. Saves up to 75" of assembly time of standard compression fittings. These fittings act similar to the way regular compression fittings work, but use a resilient O-ring for sealing, and a grip ring to hold the tube in place. The main advantages of this technology over traditional soldered copper or glued plastic are that fittings can easily be unmounted and re-used, speed of assembly, assembly when wet and that the joints are still rotatable after connection. The issues that can cause joint failure are not pushing the pipe in far enough, not having a smooth round end to the pipe, too rough a pipe surface under the O-ring and detritus in the mechanism. Deburring the end of the pipe is vital to avoid damaging the O-ring on insertion, and the pipe surface under the ring must be smooth to get an adequate seal. The pipe end should be square so it sits against the stop in the fitting and does not cause turbulence. It is quite easy to push the pipe in only as far as the grab ring, or the O-ring, and not all the way to the stop. This fitting is all brass construction. The tube release is made of acetal resin. BunaN "O" rings standard. The threads are made of brass, with sealant, when applicable.
ProductSiteLaunchDate : 2022-06-21T12:25:13.798Z
Size : 15/64" x G1/8
StreetDate : 2017-08-10T00:00:01Z
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
UnitCount : 1
UnspscCode : 40141700