Cart 2 india

Specification
Brand : CRYBY
BulletPoint1 : HIGH EFFICIENCY: The maximum pulling force of this hydraulic puller is 15T, which makes it easy to pull out even ultra-thin walls. There is a screw on the bottom of the cylinder liner puller for adjusting the cylinder diameter, you can adjust it according to your needs.
BulletPoint2 : COMPATIBILITY: This cylinder liner puller is suitable for any model with cylinder liner bore diameter between 80-135mm. Also, both dry and wet types can be used. The cylinder liner puller is used for the removal of internal combustion engines and cylinder liners.
BulletPoint3 : ERGONOMIC DESIGN: Compared with traditional cylinder liner pullers, this cylinder liner puller has an ergonomic lever design, which is more labor-saving and convenient for you to use during operation.
BulletPoint4 : DURABLE: The portable cylinder liner puller is made of 45-gauge steel with good abrasion resistance, so it is more durable and can be used for a long time.
BulletPoint5 : EASY TO OPERATE: This cylinder liner puller is easy to operate and requires no effort, saving your time and energy. Due to its simple structure, you can easily install it without much effort and time.
ExteriorFinish : NO
ExternallyAssignedProductIdentifier : 7679125599930
ExternallyAssignedProductIdentifier1 : 0765954755146
ExternallyAssignedProductIdentifier2 : 765954755146
FitType : Universal Fit
GpsrSafetyAttestation : 1
IncludedComponents : Package Content: 1 x Piston Pin Removal Tool.
IncludedComponents1 : 1* Cylinder Puller
IncludedComponents2 : Other Accessories for Use
IsAssemblyRequired : 1
ItemName : CRYBY 15T Cylinder Puller, Universal Hydraulic Cylinder Liner Puller Tool Set Wet and Dry Cylinder, Steel Diesel Engine Liner Puller Tool for Auto Repair, Maximum Stroke (Piston Push Rod) 5cm/1.97In
ItemPackageDimensions_Height : 16 centimeters
ItemPackageDimensions_Length : 65 centimeters
ItemPackageDimensions_Width : 25 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : automotive-puller-sets
Manufacturer : LOHONG
Material : #45 Steel
ModelName : 15T Cylinder Puller
ModelNumber : Lohong0000244
NumberOfItems : 1
PartNumber : Lh0000244
ProductDescription :

Specification

Max. Pulling Force: 15T

Material: #45 Steel

Maximum Stroke (Piston Push Rod): 5cm/1.97in

Weight: 18kg/39.68lbs

How to Use

1. According to the model you need to disassemble, choose the pull plate and connecting rod (the connecting rod is divided into two lengths).

2. Connect the connecting rod with the cylinder lifter, the steering knuckle and the pull plate.

3. Twist the steering knuckle of the cylinder puller to a right angle with the connecting rod. The straight side of the pull plate is parallel to the connecting rod and passes through the cylinder liner so that the small diameter of the pull plate is locked into the inner diameter of the cylinder liner.

4. Sleeve the two support tubes onto the diagonal cylinder head screws.

5. Pass the beam of the cylinder puller into the slideway of the lifting gear, and put both ends of the beam into the groove of the support tube.

6. Screw the hydraulic assembly into the lifting gear (pay attention to the center hole on the beam) and tighten it.

7. Check whether the pull plate, beam and support tube are accurately positioned.

8. Transport the small plug of the hydraulic assembly with a pressure rod, and the cylinder sleeve can be pulled out smoothly.

Package Included

1* Cylinder Puller

Other Accessories for Use

Notes

1.The extension of the cylinder push rod must not exceed 50mm.

2.Please allow the slight color difference caused by the shooting light and 1-3cm error due to manual measurement, and make sure you do not mind before ordering.

ProductSiteLaunchDate : 2024-04-18T09:21:28.220Z
Style : Harmonic Balancer Puller Set & Seal Driver Set
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
UnitCount : 1
UnspscCode : 25170000
WarrantyDescription : NO