Cart 2 india

Specification
Brand : MTM Hydro
BulletPoint1 : Includes 1 x 5' Hose Length Enough for any Stove + Hose Clamps, 1 x CU-VS Vacuum Switch and 1 x PU-VS Vacuum Switch
BulletPoint2 : Compatible with all Englander Pellet Stoves (2006 and newer), including: 10-CDV, 10-CPM, 25-CAB80, 25-CB120, 25-CBEP, 25-CBPAH, 25-EP, 25-EPI, 25-IP, 25-PAH, 25-PDV, 25-PDVC, 25-PI (Post: 2006), 25-PUF, 25-SSP01
BulletPoint3 : High pressure switch opens on pressure rise
BulletPoint4 : Internal location helps prevent tampering
BulletPoint5 : Set point adjustment is easy with range screw located inside conduit enclosure
CircuitType : 3-way
Color : White
ConnectivityProtocol : X-10
ConnectorType : Plug In
ControlMethod : touch
CurrentRating : 3 amps
ExternallyAssignedProductIdentifier : 3481064192790
ExternallyAssignedProductIdentifier1 : 0655726499920
ExternallyAssignedProductIdentifier2 : 655726499920
IncludedComponents : Switches, Hose
InternationalProtectionRating : IP67
ItemName : MTM Hydro 21.0022 4.5 Vacuum Switch
ItemPackageDimensions_Height : 7 inches
ItemPackageDimensions_Length : 7 inches
ItemPackageDimensions_Width : 7 inches
ItemPackageQuantity : 1
ItemTypeKeyword : electronic-pressure-switches
LightType : Non-Illuminated
LowerTemperatureRating : 70 degrees_fahrenheit
Manufacturer : MTM Hydro
Material : Plastic
MaximumOperatingPressure : 700 pounds_per_square_inch
ModelName : XHFY2004G Series P=0.28"W.C
ModelNumber : ENGLANDER AIR KIT
MountingType : Surface Mount
NumberOfItems : 3
NumberOfPorts : 1
NumberOfPositions : 3
OperatingVoltage : 250 volts_of_alternating_current
OperationMode : ON-OFF
PartNumber : 21.0022
ProductDescription : Englander Pellet Stove Vacuum Hose and Switch Kit Englander Pellet Stove Vacuum Pressure Hose and Switch Kit, includes 5 feet of hose (way more than enough), clips, and two vacuum switches (PU-VS and CU-VS). Fits ALL England's Stove Works Pellet Stoves to include: Englander, Summers Heat and Timber Ridge, manufactured in 2006 and later. Englander's double auger pellet stoves are some of the most popular pellet stoves in the world (PDV, PDVC models). For E1 code followed by an E2 code at or during startup: On the top or the back of the combustion blower manifold, there is a hose connected to the pressure switch. This hose is made of low-temperature silicon which, dries out overtime where it connects to the manifold and becomes brittle. Air will leak around the hose and this point and the pressure switches contacts will open and trigger the error code. This hose is longer than it needs to be and can be cut a few times. Simply cut off about an inch or somewhere up the hose to a point that’s not brittle and reinsert the hose back on the barb. The vacuum switch sensor needs to see a draw of negative pressure (suction) of at least 0.05" WC (water column) to close the electrical contacts. The vacuum hose from this switch connects directly to the rear of the stove's firebox. The controller DOES NOT read any output from this switch and will not throw any specific code if the switch is not working. In all applications where this switch is used, it is connected to the feed circuit to cut power to the auger motor. In stoves that use two auger motors, it is on the upper auger motor circuit.
ProductSiteLaunchDate : 2023-06-20T17:38:57.410Z
SpecificationMet : UL
SupplierDeclaredDgHzRegulation : not_applicable
SwitchType : Power Diode
TerminalType : Spade
UnitCount : 3
UnspscCode : 39122200
UpperTemperatureRating : 100 degrees_fahrenheit
ValveType : pressure switch