Cart 2 india

Specification
Brand : Dayton
BulletPoint1 : 1/20 hp, 71 RPM, 0.62 amps, 90 Volts DC
BulletPoint2 : Torque 40 inch pounds
BulletPoint3 : Rotation = Reversible; Shaft: 1/2" x 1"
BulletPoint4 : Over Hung Pounds = 90
BulletPoint5 : One Year Manufacture Warranty
ExternallyAssignedProductIdentifier1 : 0663001412724
ExternallyAssignedProductIdentifier2 : 663001412724
IncludedComponents : No
ItemName : Dayton DC Parallel Shaft TENV Permanent Magnet Gear Motor 71 RPM, 1/20hp 90 Volts DC Model 6Z915
ItemPackageDimensions_Height : 8 centimeters
ItemPackageDimensions_Length : 13 centimeters
ItemPackageDimensions_Width : 9 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : permanent-magnet-motors
Manufacturer : Dayton
Material : Copper
ModelName : gearmotor
ModelNumber : Genericy3wfg2xnop-13
NumberOfItems : 1
PartNumber : 6Z915
ProductDescription : 1. The DC motor adopts exactness machining, magnetic material treatment and insulation treatment, and its function is stable and .
2. The DC motor has a large torsion , not only has low noise, but also has Durability-Optimized（耐用性优化）.
3. The motor adopts wear metal gears, which can prevent teeth from breaking and prolong the service life of the motor.
4. The motor adopts pure copper wire coil, which has the characteristics of low heat and low loss.
5. The DC motor can cooperate with the governor to control the speed, and it can be CW and CCW.

Specification:
Item Type:DC Permanent Magnet Motor
Item Type:DC Permanent Magnet Motor
Model: 31ZY
Type: Permanent Magnet DC Motor
Rated Voltage: 6-24 (V)
Parameters: (Corresponding to the Table Below According to the Title Speed) Using Voltage V
Operating Voltage (V)6V12V12V24V24V24V
No Load Current (mA)≤180≤110≤350≤40≤100≤200
No Load Speed (rpm)400040008000350050008000
Rated Torsion (g.cm)100100200120200200
Rated Speed (rpm)320032006500290840006600
Rated Current (A)≤0.8≤0.5≤1.6≤2.3≤0.6≤1.0
Locked Rotor Torsion (g.cm)≥500≥600≥1000≥669≥850≥1200
Locked Rotor Current (A)≤3.3≤2.3≤6.5≤1.06≤2.0≤4.4CCM2 DC Motor Speed Regulator Product Output
DC Motor Regulator CW CCW Control
This governor uses PWM speed control technology, which has the characteristics of high conversion efficiency, wide speed range and Durability-Optimized（耐用性优化）. All use imported STMicroelectronics original chips, which have been tested for voltage, current, function, etc. before leaving the factory, and the circuit is stable and .
Technical Parameter:
Model: CCM2
Working Voltage: DC10V-30V
Control Power: 12V x 3A=36W, 24V x 3A=72W Greater than 24V, Maximum 120W
Rated Current: 3A
Maximum Current: 5A
PWM Pulse Width Adjustment System Range: 5%-95%
Potentiometer: Value B10K, Wire Length 20CM, Opening 8mm,
Output Voltage: About 0- of the Input Voltage
Speed Governor Size: Approx. 74 x 47 x 28mm / 3 x 2 x 1.1in
Potentiometer is used for speed regulation
CW CCW switches are used to control CW, CCW, and stop
Note:
Motor
1. When you use the motor, there should be no binding objects. For example, the adhesive should not into the bearing through the rotating shaft, which will hinder the of the motor.
2. The rotation of the shaft may have the opposite effect on the life of the motor. In order to prolong the life, please check whether your load is in accordance with the regulations. Do not overload or have objects that hinder rotation at the end of the shaft.
3. Manufactured into an eccentric heavy radiation load, which is harmful to the life of the motor.
4. Do not store in surrounding high temperature or extreme humidity, and do not place in corrosive gas, which will reduce the effect of the motor.
5. Do not run the motor in the surrounding high temperature and humidity.
6. When soldering is needed on the positive and negative motor terminals of the power supply, the temperature of the soldering iron is 340℃±40℃, and the heating time is within 3 seconds. Do not deform the plastic. Let the soldering spot into the motor or break the end of the wire during work. Motor function declines.
7. Do not let the motor shaft get stuck. When the power is supplied, the motor will overheat in a short time and its accessories will be burnt.
8. Due to the lack of skills of the staff, the quality of the motor cannot be guaranteed when it encounters the things mentioned in the manual, or the superficial judgment is obviously fault.
9. Supply the specified power and be sure that it is within the range of measurable requirements.
10. The installation of pulleys or gears should not be abnormally aggravated when pressed in.
11. When installing the motor, if the screw is too long, it will cause between the motor itself and the rotor, which will affect the characteristics.
Governor
1. The input of the DC motor speed controller is DC, and it cannot be directly connected to AC (such as household 220V AC motors), otherwise it will burn out.
2. The positive and negative poles of the DC power supply cannot be reversed, otherwise the governor will be damaged.
3. The motor can be positive or negative. When the running direction is inconsistent with the expectation, the direction can be changed by adjusting the wire sequence.
4. The potentiometer knob can change the duty cycle of the governor output, thereby changing the motor speed

How to Use:
[Connection Method] 1. The red wire is connected to the positive electrode, the black wire is connected to the negative electrode, and the output direction is clockwise CW.
2. The red wire is connected to the negative pole, the black wire is connected to the positive pole, and the output turns to CCW counter clock wise.

Package List:
1 x Motor
1 x Governor
1 x CW CCW Switch
1 x Knob
1 x Washer

Note:
Please note that the new type and
ProductSiteLaunchDate : 2005-09-25T00:00:00-00:00
Size : 12V8000RPM
Speed : 71 rpm
Style : 12V8000RPM
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
UnspscCode : 26101200
Voltage : 90 volts