Cart 2 india

Specification
AgeRangeDescription : Adult
Brand : Fasco Epoxies
BulletPoint : Light Gray
BulletPoint1 : High Impact Resistance
BulletPoint2 : Saltwater/Freshwater Resistant
BulletPoint3 : Excellent adhesion to Wood, Steel, Aluminum, Soft Metals, Concrete, Ceramic, Fiberglass, Composites
BulletPoint4 : Low Shrinkage; Withstands Wide Range of Temperatures
BulletPoint5 : Can be Mixed with Sand to Create a High Strength Mortar for Concrete Repair
Color : Orange
ColorCode : #FFFFFF
ExternallyAssignedProductIdentifier : 4996624001027
ExternallyAssignedProductIdentifier1 : 0819794022095
ExternallyAssignedProductIdentifier2 : 819794022095
ExternallyAssignedProductIdentifier3 : 00727908417067
FinishType : Gloss
FitType : Universal Fit
Hazmat : 9
Hazmat1 : HELIUM, REFRIGERATED LIQUID
Hazmat2 : UN1963
Hazmat3 : 2.2
IncludedComponents : Caliber 13570 Alumi-Skin Metal Protectant
IndoorOutdoorUsage : outdoor
IsWaterproof : False
ItemForm : Liquid
ItemName : Fasco Epoxies #103LVX 2:1 Marine Grade Epoxy for Fiberglass, Cloth, Wood, Boat Building and Repair (1.5 Gallon Kit Medium Hardener)
ItemPackageDimensions_Height : 2.5 inches
ItemPackageDimensions_Length : 7.5 inches
ItemPackageDimensions_Width : 2.5 inches
ItemPackageQuantity : 1
ItemTypeKeyword : boating-painting-supplies
ItemVolume : 12 milliliters
Manufacturer : Fasco Epoxies Inc.
Material : Resin
ModelName : 13570
ModelNumber : 13570
NumberOfBoxes : 1
NumberOfItems : 1
OemEquivalentPartNumber : 129007
PaintDilutionPercentage : 100
PaintType : Enamel
PartNumber : 13570
Pattern : Solid
ProductDescription : 103 LVX Epoxy laminating epoxy is a new and improved formula. It provides high tensile strength while maintaining a very low viscosity to aid in wetting out fiberglass. This enables the laminator to produce high tensile strength lay-ups with maximum “wetting out” and a minimum of bubbles.
103 LVX can be used on warehouse docks, floors, sidewalks, walls, and concrete. 103 LVX can be mixed with sand to fill in large holes and cracks in concrete and has enough strength to withstand heavy forklift traffic. 103 LVX seals against leaks without shrinkage and is also used to laminate fiberglass cloth to existing fiberglass, wood, metal, or concrete.

Application: Mix very well, scraping down the sides of the mixing bucket to ensure that all of the resin and hardener gets mixed together.
Application for Heavy Duty Non-Skid Surface for Metal, Concrete, Wood, or Fiberglass:
1. Surface must be clean, dry, and free from oil or grease.
2. Mix the 103 LVX kit. Roll or brush evenly on surface.
3. While epoxy is wet, broadcast quartz aggregate evenly on surface (other non-skid particles may be substituted for quartz). The epoxy should stay wet enough to receive the aggregate for at least 1 hour. Use aggregate size in accordance to roughness desired - #30-65 aggregate is an average non-skid surface.
4. Continue above procedure until entire surface is covered with aggregate.
5. Allow to dry. Sweep off loose aggregate.
6. Apply a thin coat of mixed 103 LVX epoxy over the aggregate surface. Squeegee the epoxy down tight so that there are no puddles of epoxy. The surface should have an even textured appearance.
Working Time: Mixed product must be used within 20 min.
Gel Time Thin Coats 1-2 hours - Thick Coats 20-25 Min.
Set Time Thin Coats 4-6 hours - Thick Coats 2-4 Hours.
Cure Time 24 to 72 Hours
ProductSiteLaunchDate : 2018-08-13T07:00:00.000Z
RequiredProductComplianceCertificate : California Air Review Board (CARB)
Size : 1 count (pack of 1)
SupplierDeclaredDgHzRegulation : not_applicable
SurfaceRecommendation : Exterior
UnitCount : 1
UnspscCode : 49000000
VolumeCapacityName : 3 quarts
WaterResistanceLevel : water_resistant