Cart 2 india

Specification
Brand : MOLLIFII
BulletPoint1 : ✅ 3/8 Inch Drive x 18 mm 6-Point Flare Nut Crowfoot Wrench, Mfr: WCF16218-A
BulletPoint2 : ✅ Optimized for Engagement, Access, and Strength – Our deep, 6-point design maximizes your contact with fittings and prevents slipping
BulletPoint3 : ✅ Reinforced Jaw Strength – We reinforced our wrenches with material where it matters most to avoid high stress concentrations and prevent the jaws from spreading
BulletPoint4 : ✅ 15-Degree Offset Increases Access Angles – The jaw opening is offset 15 degrees from the center of the wrench so that it can be flipped over to gain additional access angles
BulletPoint5 : ✅ Electroless Nickel Plating for Corrosion Resistance – The electroless nickel plating finish is easy to wipe clean, highly resistant to corrosion, and has a low environmental impact compared to conventional hexavalent chrome plating
Color : One Color
ExternallyAssignedProductIdentifier : 4670264596449
ExternallyAssignedProductIdentifier1 : 778272956423
ExternallyAssignedProductIdentifier2 : 0778272956423
FinishType : Powder Coated
ItemLength : 13.75 inches
ItemName : MOLLIFII 3/8 Inch Drive x 18 mm 6-Point Flare Nut Crowfoot Wrench, Mfr: WCF16218-A
ItemPackageDimensions_Height : 1 centimeters
ItemPackageDimensions_Length : 3 centimeters
ItemPackageDimensions_Width : 2 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : open-end-wrenches
Manufacturer : MOLLIFII
Material : Alloy Steel
ModelName : WCF16218-A
ModelNumber : WCF16218-A
NumberOfItems : 1
OperationMode : Mechanical
PartNumber : OEIPSMK
ProductDescription : WCF16218-A Flare Nut Crowfoot Wrench sizes scale optimally with fitting depths to achieve the best possible combination of engagement, access, and strength. Our design is leaner than conventional 6-point crowfoot wrenches, giving you more room to work in tight spaces. The wrenches are abrasive blasted to create a smooth, satin finish. Our electroless nickel plating process applies a uniform, corrosion resistant coating to the entire tool surface. Each crowfoot wrench has a permanent high-contrast size marking engraved on the side. The wrenches are made entirely in the USA with USA-sourced materials. Most of the steps, including machining, broaching, blasting, plating and engraving, take place at manufacturing facility in Grand Rapids, Michigan.Optimized for Engagement, Access, and Strength – Our deep, 6-point design maximizes your contact with fittings and prevents slippingReinforced Jaw Strength – We reinforced our wrenches with material where it matters most to avoid high stress concentrations and prevent the jaws from spreadin15-Degree Offset Increases Access Angles – The jaw opening is offset 15 degrees from the center of the wrench so that it can be flipped over to gain additional access anglesElectroless Nickel Plating for Corrosion Resistance – The electroless nickel plating finish is easy to wipe clean, highly resistant to corrosion, and has a low environmental impact compared to conventional hexavalent chrome platingUniform Coverage and Better Fit – The electroless plating process applies a uniform coating to the entire tool surface; by comparison, electroplating, including conventional chrome plating, has varying thickness across the tool because the plating thickness depends on the electric current density at each point on the toolManufactured in Michigan – flare nut crowfoot wrenches are made entirely in the USA with USA-sourced materials; most of the steps, including machining, broaching, blasting, plating and engraving, take place at manufacturing facility in Grand Rapids, Michigan
ProductSiteLaunchDate : 2024-06-26T09:36:48.281Z
Size : One Size
SupplierDeclaredDgHzRegulation : not_applicable
UnitCount : 1
UnspscCode : 27111700