Ace Hydraulic Motor for Open & Closed Center Systems w/Integral Needle Valve Farmer Bob's Parts BAC-75-HYD-204

Imported from USA | Ships in 10 working days

5% instant discount on non COD

1

₹ 88200/-

The price at cart2india.com is inclusive of custom duties, GST, freight forwarding and other charges.

Free Shipping across India. Powered by BlueDart

Product Information


Specification
Brand : Farmer Bob's Parts
BulletPoint1 : Comes With Seal Support Spacer, 2 Couplers & Motor Bolts Ace Pump Hydraulic Motor 4 GPM for Open and Closed Center Systems with Integral Needle Valve. Used on Ace Tractor Hydraulic System Driven Centrifugal Pumps.
BulletPoint2 : 41370, 01441370, 2336014-41370, BAC75HYD204, BAC-75-HYD-204
BulletPoint3 : 204 Series
BulletPoint4 : Motor
BulletPoint5 : hp: 1 hp
Color : Green
ExternallyAssignedProductIdentifier1 : 0731515758338
ExternallyAssignedProductIdentifier2 : 731515758338
Horsepower : 1 horsepower
ItemName : Ace Hydraulic Motor for Open & Closed Center Systems w/Integral Needle Valve Farmer Bob's Parts BAC-75-HYD-204
ItemPackageQuantity : 1
ItemTypeKeyword : hydraulic-motors
Manufacturer : ACE Pump
Material : Steel
ModelName : EX120-2 EX120-3 Blower Motor
ModelNumber : EX120-2 EX120-3 Blower Motor
NumberOfItems : 1
PartNumber : BAC-75-HYD-204
ProductDescription : The Seal Support Spacer is designed to provide additional support for the cartridge type (L) hydraulic motor seal. The retaining ring is removed from the hydraulic motor when the spacer is installed allowing the hydraulic seal to rest directly against the Seal Support Spacer. Pressure spikes in excess of 3000 PSI may occur when hydraulic oil is returned to the hydraulic valve and the pump is turned off in the neutral position. The spacer supports the motor seal during momentary spikes and prevents seal case distortion, which results in seal leakage. Using the cartridge type seal with the Seal Support Spacer will prevent seal failures when returning hydraulic oil to most hydraulic valves. Assembly: 1. Install the seal support spacer into the coupler cavity: S200 - Place the end with the large diameter against the pump mounting frame rear bearing retaining ring. S300 - Insert seal support spacer into coupler cavity against the pump mounting frame rear bearing retaining ring. Orientation is not important for S300. Do not re-install the shaft seal retaining ring in the motor drive plate. 3. Pack open areas of coupler cavity with grease. 4. Install motor aligning the shaft tang with coupler slot. 5. Install 4 motor bolts. Disassembly: 1. Remove four motor bolts. 2. Remove motor from pump assembly. Note: Do not lose coupler. 3. Remove grease from coupler cavity. 4. Remove motor shaft seal retaining ring from drive plate. Warning: Never operate the hydraulic motor when detached from pump mounting frame. Hydraulic seal may blow out causing bodily injury. 5. Inspect motor seal. Replace motor seal if leaking, seal casing is deformed, or lips appear damaged.
ProductSiteLaunchDate : 2019-08-27T14:33:27.814Z
Speed : 4 rpm
SupplierDeclaredDgHzRegulation : unknown
UnitCount : 1
UnspscCode : 40141600
Voltage : 115 volts

Questions & Answers

Have a question? Ask experts

?
No question found

Ratings & Review

Rating Breakdown (average)

5*
0
4*
0
3*
0
2*
0
1*
0

No reviews found.

Have an opinion on this page? Let's hear it.