Cart 2 india

Specification
Brand : DiGiYes
BulletPoint1 : Suitable for stepper motor: 57, 60, 86 type 2-phase (4-wire, 6-wire, 8-wire). fit for hybrid 2-phase stepper motors (Outer diameter: 57, 60, 86mm).
BulletPoint2 : The maximum drive subdivision is 128, the maximum number of steps can reach 25600, suitable for high-precision control systems.
BulletPoint3 : Input voltage DC 20-50V, recommended for 24V-48V.
BulletPoint4 : The control signal voltage DC 5-24V is universal and does not require a series resistor. Output peak-current: 1.4 - 5.6A.
BulletPoint5 : DM556 is a high-performance and highly reliable stepper driver with advantages such as low noise, low vibration, high precision, and fast response.
ExternallyAssignedProductIdentifier : 3458519479041
IncludedComponents : No
ItemName : DiGiYes CNC Digital Stepper Driver DM556 Stepper Motor Driver 2-Phase DC 20-50V Max 5.6A 128 Subdivision Fit for Nema 23 24 34 and Nema 34 stepper motor
ItemPackageDimensions_Height : 1.42 inches
ItemPackageDimensions_Length : 5.71 inches
ItemPackageDimensions_Width : 3.94 inches
ItemPackageQuantity : 1
ItemTypeKeyword : motor-speed-controllers
Manufacturer : DiGiYes
Material : Copper
ModelNumber : Aramox4orghv5u6w
NumberOfItems : 1
PartNumber : EMD_21Q
ProductDescription : Parameter Information:
Model: DM556
Input Voltage: DC 20-50V(recommended 24V-48V)
Current: 1.4 - 5.6A
Features:
- 8 dip switches SW1-SW8, detailed settings can be found in the driver panel diagram. SW1-SW3 is used to set the output current of the driver. SW4 is used to set the automatic half / full current function of the driver, usually set to OFF. OFF indicates that the static current is half of the dynamic current, while ON indicates that the static current is the same as the dynamic current. Changing its state twice within 2 seconds will automatically adapt to the motor parameters. SW5-SW8 is used to set the microstep subdivision of the driver.
- The drive has two indicator lights, red and green. The green light is the power indicator light, which stays on continuously when the driver is powered on; The red light is the fault indicator light. When overvoltage or overcurrent faults occur, the fault light remains on. After clearing the fault, the red light goes out. When the drive malfunctions, only by re powering on and re enabling can the fault be cleared.
Place of Application:
- Suitable for various small and medium-sized automation equipment and instruments, such as 3D printers, engraving machines, marking machines, cutting machines, laser phototypesetter, plotters, CNC machine tools, automatic assembly equipment, etc.
- Suitable for stepper motor: 57, 60, 86 type 2-phase (4-wire, 6-wire, 8-wire).
- Fit for Nema 23 Nema 24 and Nema34 stepper motor, fit for hybrid 2-phase stepper motors (Outer diameter: 57, 60, 86mm).
Note:
- After the user completes the wiring, when the first power is turned on, the motor parameters must be automatically recognized through SW4 (changing the AW4 state twice within 2 seconds, automatically adapting the motor parameters). ackage Include:
1 x DM556 Stepper Motor Driver
ProductSiteLaunchDate : 2024-05-14T06:17:11.972Z
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredDgHzRegulation1 : not_applicable
SupplierDeclaredDgHzRegulation2 : not_applicable
SupplierDeclaredDgHzRegulation3 : not_applicable
SupplierDeclaredDgHzRegulation4 : not_applicable
SupplierDeclaredDgHzRegulation5 : not_applicable
UnspscCode : 26111500
Voltage : 72 volts