Cart 2 india

Specification
Brand : WAAZVXS
BulletPoint1 : Model Number: GDL70-63F-24Z/12 Long Shaft
BulletPoint2 : Drive: Motor ; Voltage: 380V
BulletPoint3 : Power: 12Kw; Current: 20.0A
BulletPoint4 : Frequency: 800Hz
BulletPoint5 : Number of poles: 4P
Color : 380V
ExternallyAssignedProductIdentifier : 7807792531025
ExternallyAssignedProductIdentifier1 : 840403770489
ExternallyAssignedProductIdentifier2 : 0840403770489
IncludedComponents : removable milling chuck, MT2-ER32 tapper accessory, R8 spindle taper
ItemName : WAAZVXS GDL70-63F-24Z/12KW Automatic Tool Changer Spindle 380V Air Cooled Spindle Motor 63F Tool Holder for Wood CNC Router
ItemPackageDimensions_Height : 1 centimeters
ItemPackageDimensions_Length : 3 centimeters
ItemPackageDimensions_Width : 2 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : power-milling-machines
Manufacturer : WEIWEIBEIER
Material : metal
MaximumPower : 1300 watts
MaximumRotationalSpeed : 2250 rpm
ModelName : WWBR
ModelNumber : WWBR
NumberOfBoxes : 1
NumberOfItems : 1
PartNumber : WWBR
PowerSourceType : AC
ProductDescription : 1. Our ceramic ball bearing spindle uses 4 ceramic ball bearings.2. Ceramic ball bearings are resistant to high temperature and low heat, and are usually 3-5 degrees lower than steel ball bearings during use.3. Ceramic ball bearings have low friction, low noise and long service life.4. If the spindle is to be used for aluminum or hardwood, ceramic ball bearings are better than steel ball bearings.Main Application: Engrave for wood,PCB,PVC, PM-MA,plastic,duotone board(ABS)and etc nonmetal, also can engraveon gold,silver,copper, aluminium,Pb etc soft metal surface working.Not only full of power, but also comfortable and quietSilent as low as 18 decibels, creating a comfortable sleeping environment for you and liberating sensitive earsDuring the storage and transportation of the spindle, the state of the high-speed grease inside the bearing will change, and the customer should run it at a low speed for 30 minutes. Then slowly increase at 3000 rpm, running for 20 minutes each time . The spindle and inverter should work together. The specifications and parameter of the inverter need to match the spindle parameters. (Because the high-speed grease inside the bearing changes, the sound may not sound normal when you get the spindle. Please run it for 30 minutes or more, the sound will be normal.)Connect the main shaft of the inverter. The power cord of the three- inverter phase should be welded to the 1 (U), 2 (V), 3 (W) and 4 pins of the plug. After turning on the power, observe whether the spindle axis of rotation is consistent with the direction. If it is inconsistent, turn it off immediately, and replace the two wires of the three-phase power supply connected to the inverter and the spindle.During normal operation, the air-cooled spindle often generates heat. Please always check whether the air-cooled spindle box and the air duct are blocked by dust. If the dust is blocked, clean it up in time. If it is not cleaned, it is easy
ProductSiteLaunchDate : 2024-05-13T08:18:29.071Z
Size : One Size
Speed : 2250 rpm
Style : RCOG-16V MT2
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
UnitCount : 1
Voltage : 110 volts_of_alternating_current
Wattage : 600 watts