Cart 2 india

Specification
Brand : Orbit
BulletPoint1 : For making polyethylene pipe connections in sprinkler systems
BulletPoint2 : Stainless steel teeth grip, and a special O-ring creates a rotatable, watertight seal
BulletPoint3 : Immediately pressurize the system with no wait time for joints to cure
BulletPoint4 : Built-in removal for 1/2-in. and optional tool for 3/4-in. and 1-in. facilitate easy removal and reuse of fittings
BulletPoint5 : For valve out connections only. Use PVC-Lock with Schedule 40 PVC pipe for constant pressure applications
Color : Black
ConnectorType : Barb
ExteriorFinish : Stainless Steel
ExternallyAssignedProductIdentifier : 00834836000275
ExternallyAssignedProductIdentifier1 : 046878316843
ExternallyAssignedProductIdentifier2 : 0046878316843
ExternallyAssignedProductIdentifier3 : 00046878316843
GpsrSafetyAttestation : 1
IncludedComponents : Fitting
ItemLength : 100 feet
ItemName : Orbit 31684 - 3/4" X 3/4" X 1" Blu-Lock Bullhead Tee
ItemPackageDimensions_Height : 8.9916 centimeters
ItemPackageDimensions_Length : 4.3942 centimeters
ItemPackageDimensions_Width : 6.4008 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : automatic-lawn-irrigation-tubing
Manufacturer : Orbit Irrigation
Material : Stainless Steel
MaximumPressure : 50 pounds_per_square_inch
ModelName : TANIQIACAwntz6fe4gx
ModelNumber : 31684
NominalWallThickness : 0.05 inches
NumberOfItems : 1
NumberOfPieces : 1
PackageLevel : unit
PartNumber : 31684
ProductDescription : This 1/2" dripline is a .600" ID X .700" OD (17mm) black polyethylene, pressure compensating drip line with pre-installed in-line drip emitters that provide high uniformity and even distribution of water over longer lengths and uneven terrain. May be hung on a wire, laid on the ground or buried, making it an economical choice for vineyards, orchards, and row crops.As with our blank poly tubing, additional PC emitters and/or 1/4" micro line can be added to this drip line. When adding additional drippers, do not punch too close to the pre-installed emitters and take care not to exceed the maximum flow rate for the specifications and run length. For optimal operation we recommend not exceeding 200 ft per run. Keep in mind that operating pressure and emitter spacing can affect the optimal operation and run length recommendations. Lower pressure and closer emitter spacing would perform better at shorter run lengths. If using higher operating pressure and wider emitter spacing you can achieve consistent emitter flow rate in some longer runs. Keep in mind that uneven terrain and varying environmental factors may affect the operation as well.Very effective method to irrigate crops in difficult topographical conditions, low and varying water pressures and where longer laterals are required. This drip line is compatible with our 1/2" Perma-Loc fittings. Do to the tightness the tubing must be rolled it often has a more oval shape when first opening a new roll. There also may be some slight kinking in the center of the roll and where the banding is, this will not hinder the use and performance of the tubing. These issues will smooth out after un-banding and some sun exposure and the ovalness will round out over time or with a few uses (pressurization/depressurization).Features:Built-in filtration provides superior clog resistanceLarge turbulent flow path allows particles to pass freelyConsistent discharge over a pressure range of 7 - 60 PSICV (coefficient of variation) values
ProductSiteLaunchDate : 2023-09-26T22:34:51.725Z
Style : Emitter Spacing 9"
SupplierDeclaredDgHzRegulation : not_applicable
UnitCount : 1
UnspscCode : 40141700