Cart 2 india

Specification
Brand : Shars
BulletPoint1 : MFG SKU #: 303-3001
BulletPoint2 : Brand: Shars Tool
BulletPoint3 : Minimum Measuring Range: 0.315", 8mm / Maximum Measuring Range: 0.394", 10mm
BulletPoint4 : Bore Depth: 1.73
BulletPoint5 : Setting Ring: 0.31496
BulletPoint6 : Contact Points: 3
BulletPoint7 : Resolution: 0.00005"
BulletPoint8 : Accuracy: ±0.00015"/0.004mm
CustomerPackageType : Standard Packaging
ExternallyAssignedProductIdentifier : 7894789938554
ExternallyAssignedProductIdentifier1 : 0000830330018
ExternallyAssignedProductIdentifier2 : 000830330018
ExternallyAssignedProductIdentifier3 : 00049659530568
IncludedComponents : 1 micrometer, 1 setting ring, 1 extension rod, 1 adjusting wrench, 1 battery
ItemName : SHARS .315 - .394" Electronic 3 Point Internal Micrometer .00005" New [0.00005" Resolution, ±0.00015" Accuracy] 303-3001 S]
ItemPackageDimensions_Height : 11.8 centimeters
ItemPackageDimensions_Length : 3 centimeters
ItemPackageDimensions_Width : 3 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : inside-micrometers
Manufacturer : Shars Tool
Material : Carbide
MeasurementAccuracy : ±0.00015"
ModelNumber : 303-3001
NumberOfBoxes : 1
NumberOfItems : 1
PackageLevel : unit
PartNumber : 303-3001
ProductDescription :

• This versatile and self-centering 3 point internal micrometer are designed for accurate and repeatable measurement of internal diameter. Measurement can be taken closed to the bottom of a blind hole or in a deep hole with extensino rod. 3 point anvils evenly spaced at 120 degree apart, contact the internal wall surface and find the true alignment with the bore axis for accurate ID measurement
• Calibration procedure: 1) Before placing the micrometer into the supplied ring gage, press and hold the on/off/set key to go into the preset mode and use either hold or in/mm/0 key to adjust value as the ring gage diameter and toggle the decimal place by pressing the on/off/set key; Once the ring gage diameter is set in the Preset mode, press and hold the on/off/set key to exit the Preset mode. 2) Place the internal micrometer into the supplied ring gage and ensure repeatable contact with the interal bore surface 3) While the micrometer still is in the ring gage, press & hold the in/mm/0 key to set the micrometer to its preset value
• 3 Point contact with tungsten carbide measuring anvil on range above .5"
• Ratchet stop would apply constant measuring force to capture repeatable bore measurement
• Inch/mm/0 function key: short press to toggle between inch or metric; press & hold key would toggle between relative or absolute measurement data
• Hold function key: By pressing this key to hold the current bore measurement value regardless the movement of the micrometer thimble, allowing the user to retract the micrometer out of bore to faciliate easy reading. Deactivate this function by pressing the HOLD funciton key again
• Auto shut-off after 5 minutes and retain current measurement at power-on if not rotating the thimble
• Included setting ring for easy calibration
• 1.968" Long Extension rod included for measuring deep hole
• SPC data port avaliable, connection cable (sku# 303-3597) sold separately

ProductSiteLaunchDate : 2024-04-30T16:21:54.066Z
Range : 4-5"
Resolution : 0.001"
Size : 4-5"
Style : Vernier
SupplierDeclaredDgHzRegulation : not_applicable
UnitCount : 1