Cart 2 india

Specification
Brand : Hobby Homebrew
BulletPoint1 : Plumb your false bottom to your ball valve sticking out inside the brew kettle or mash tun.
BulletPoint2 : Includes a special stainless steel female 1/2" NPT X 3/8" barb, 6" of 3/8" high temp tubing, and two stainless steel worm clamps.
BulletPoint3 : Will plumb 98% of false bottoms up to 15".
BulletPoint4 : Kit is all food grade made from high temp silicone tubing and Stainless Steel only.
BulletPoint5 : Tubing is our heavy weight MADE IN USA high temp silicone. All other components 304 stainless steel.
BulletPoint6 : Easy to Follow Instructions
CareInstructions : Hand Wash
Color : Gray
ExternallyAssignedProductIdentifier1 : 0733960927697
ExternallyAssignedProductIdentifier2 : 733960927697
IncludedComponents : Kit with special stainless steel female 1/2" NPT X 3/8" barb, 6" of 3/8" high temp tubing, and two stainless steel worm clamps.
ItemDisplayDimensions_Length : 30 inches
ItemDisplayWeight : 1 pounds
ItemName : Hobby Homebrew 6"" FALSE BOTTOM ADAPTER KIT = FEMALE = Fitting Kit Plumbing for Igloo Cooler Mash Tun or Brew Kettle, Gray
ItemPackageDimensions_Height : 4 inches
ItemPackageDimensions_Length : 12 inches
ItemPackageDimensions_Width : 12 inches
ItemPackageQuantity : 1
ItemTypeKeyword : beer-brewing-starter-sets
Manufacturer : Hobby Homebrew
Material : Silicone
ModelName : FALSE_BOTTOM_KIT_FEMALE
ModelNumber : FALSE_BOTTOM_KIT_FEMALE
NumberOfItems : 1
PartNumber : Does Not Apply
ProductDescription : Here's a fitting kit to plumb your false bottom to the ball valve sticking out inside your brew kettle or mash tun. This kit is all food grade made from high temp silicone tubing and Stainless Steel only. There is no brass or galvanized steel. Includes a special Female 1/2" NPT Stainless Steel 3/8" barb, 6" of 3/8" High Temp Tubing and two stainless steel worm clamps. Will plumb a false bottom up to 15". This kit will plumb 98% of all false bottoms needing a female end to connect to the tun or kettle hardware. The included special Female (FPT) barb eliminates the need for a coupler and helps deal with a certain ball valve problem 'not enough thread left' to get the coupler on. This kit is also available in Male. This kit will plumb 98% of all false bottoms needing a female end to connect to the tun or kettle hardware. The included special Female (FPT) barb eliminates the need for a coupler and helps deal with a certain ball valve problem 'not enough thread left' to get the coupler on. This kit is also available in Male. BACKGROUND: A concave or 'dome' type false bottom comes bare with only the 3/8" barb, elbow, nut, and gasket pre-assembled. It does not have the plumbing kit with it. This is that kit and fills your need for a short length (6" ought to do it) of silicone tubing to go between the barb in the center of the false bottom and your cooler or kettle side hardware. Aside from the one nut touching the cooler, the inside plumbing components don't really need to be taped or even torqued down. Just thread them on there a couple spins by hand so you can take them apart easily to clean the unit. Be sure to use our stainless steel clamps rather than galvanized, although you might find you don't need clamps at all if your heat rated tubing is tight enough. If it loosens over time you will have to replace it or start using the clamps.
ProductSiteLaunchDate : 2024-01-21T18:39:08.227Z
Reusability : Reusable
Size : 6"
SupplierDeclaredDgHzRegulation : not_applicable
UnitCount : 1
UnspscCode : 52150000