Specification Brand : Rvhouse BulletPoint1 : 【VHB Tape】3M VHB Tape 5925 is a 0.025 inch (0.6 mm) thick black double-coated acrylic foam tape with PE film liner. The modified acrylic adhesive on both sides bonds to a broad range of high, medium, and medium/low surface energy substrates including metals, glass, and a wide variety of plastics and paints, the very conformable foam provides good contact between substrates even when they are slightly mismatched BulletPoint2 : 【Features】Fast and easy-to-use permanent bonding method provide high strength and long-term durability. Creates a permanent seal against water, moisture, and more by offering better gap-filling capabilities. Pressure-sensitive adhesive bonds on contact to provide immediate handling strength BulletPoint3 : 【Multi-purposes】Suitable for solar panels of RV, car holders, LED strip lights, trim, nameplates, address plaques, signs, power strips, mirrors, hangers, toothbrush holders, picture frames, automotive decorations BulletPoint4 : 【Easy to Use】Eliminate drilling, grinding, refinishing, screwing, and welding, this foam tape is easy to install, just peel off the tape and stick it to the surface of the object. Note: Please cut a corner piece of the liner with a knife when it is hard to peel off BulletPoint5 : 【Cure Time】After application, the bond strength will increase as the adhesive flows onto the surface (also referred to as “wet out”). At room temperature, approximately 50% of ultimate bond strength will be achieved after 20 minutes, 90% after 24 hours, and 100% after 72 hours Color : Black CompatibleMaterial1 : Plastic CompatibleMaterial2 : Glass CompatibleMaterial3 : Metal CompatibleMaterial4 : Stainless Steel CompatibleMaterial5 : Wood ExternallyAssignedProductIdentifier1 : 888519074565 ExternallyAssignedProductIdentifier2 : 0888519074565 ExternallyAssignedProductIdentifier3 : 00888519074565 ItemName : 3M Double Sided Tape 1”×16.4ft VHB 5925 Black Mounting Tape Heavy Duty Waterproof Foam Tape Strong Adhesive for RV LED Strip Light Décor ItemPackageDimensions_Height : 16.2052 centimeters ItemPackageDimensions_Length : 2.794 centimeters ItemPackageDimensions_Width : 15.5956 centimeters ItemPackageQuantity : 1 ItemTypeKeyword : foam-tape LowerTemperatureRating : 10 degrees_celsius Manufacturer : Rvhouse Material : Firm Foam Material1 : Acrylic Material2 : Foam ModelNumber : 5925 NumberOfItems : 1 PartNumber : 5925 ProductDescription : Typical Physical Properties
- Color:Black. - Adhesive Type :Modified Acrylic - Foam Type :Very Conformable Acrylic Foam - Density(ASTM D3574 ):590 kg/m³ (37 lb/ft³) ¹ - Total Tape Thickness(ASTM D3652)0.6 mm (0.025 in) (25 mil) - Thickness Tolerance :±15 % - Liner :PE Film - Liner Thickness:0.13 mm (0.005 in) (5 mil) - Primary Liner Color:Red (printed) - Minimum Application Temperature:10 °C (50 °F) - Short Term Temperature Resistance:149 °C (300 °F) - Long Term Temperature Resistance:93 °C (200 °F)
Application Techniques
Clean: Most substrates are best prepared by cleaning with a 50:50 mixture of isopropyl alcohol (IPA*) and water prior to applying 3M VHB Tapes.
Exceptions to the general procedure that may require additional surface preparation include: - Heavy Oils: A degreaser or solvent-based cleaner may be required to remove heavy oil or grease from a surface and should be followed by cleaning with IPA/water.
- Abrasion: Abrading a surface, followed by cleaning with IPA/water, can remove heavy dirt or oxidation and can increase surface area to improve adhesion.
- Adhesion Promoters: Priming a surface can significantly improve initial and ultimate adhesion to many materials such as plastics and paints.
- Porous surfaces: Most porous and fibered materials such as wood, particleboard, concrete, etc. need to be sealed to provide a unified surface.
- Unique Materials: Special surface preparation may be needed for glass and glass-like materials, copper and copper containing metals, and plastics or rubber that contain components that migrate (e.g. plasticizers).