Cart 2 india

Specification
AgeRangeDescription : No
Brand : SICOLAS
BulletPoint1 : Our mosaic pins have been vacuum-pumped to remove air bubbles. The resin is pulled in with a high-end vacuum, which pulls the glue down, and removes any small bubbles. The pins are cured afterward and lastly polished and burrs removed.
BulletPoint2 : Material:brass, stainless steel and copper,mosaic pins are hand-crafted for knife maker
BulletPoint3 : It is better for approximately 1/8" extends beyond the scales before you start sanding.Diameter: 5mm,Length:9.5cm,You get 1 piece of mosaic pin stock with each order for knife handles.You can cut any length as your knife handle thickness,great gift for your custom knives craftsman
BulletPoint4 : It is possible to drill a knife blank's pin holes larger (or create your own pin hole locations).Once your knife handle has been built, it is recommended to keep the exposed surfaces of the mosaic pin protected with clear varnish/lacquer.
BulletPoint5 : You simply need to use drill bits intended for drilling metal, which are capable of drilling through hardened stainless steel. This method is recommended because you be able will get the exact fit you are looking for when using our mosaic pins.
Color : B5mm
IncludedComponents : No
ItemLength : 3.74 inches
ItemName : SICOLAS Mosaic Pivot Pins for Knife Handle, Blank Pocket Knives Scales Grips Shaft, EDC Hunting Folding Knives Fastener, 9.5cm (B5mm)
ItemPackageDimensions_Height : 0.4 inches
ItemPackageDimensions_Length : 5 inches
ItemPackageDimensions_Width : 4 inches
ItemTypeKeyword : fixed-blade-tool-knives
Manufacturer : SICOLAS
PartNumber : USAyun gui mosaic
ProductDescription : Mosaic Pivot Pins for Knife Handle, Blank Pocket Knives Scales Grips Shaft, EDC Hunting Folding Knives Fastener
Brass, Copper, Stainless Steel for EDC Folding Pocket Knives Pin
This unique mosaic pin was hand-crafted by an expert.
Add that extra bit of flair to your knife handle!
This pin can be used for knife making, metal work, jewelry etc.
It can be used as a solid pin or sliced into thin pieces for inlays.
The pattern exists along the entire pin length.
We use only the highest quality brass, copper and stainless steel.
This pin requires a hole of 1cm to be drilled into the handle of your knife.
You simply need to use drill bits intended for drilling metal, which are capable of drilling through the steel type of your knife
Do not expose to excessive heat when cutting the pins (it will become damaged over 95 degrees celsius).
Do not polish them too much.Use only sandpaper for polishing.
Use 1200 grit sandpaper for final polishing.And last, use lacquer or oil.
Our mosaic pins have been vacuum-pumped to remove air bubbles.
The resin is pulled in with a high-end vacuum, which pulls the glue down, and removes any small bubbles.
The pins are cured afterward and lastly polished and burrs removed.
The center of the mosaic pin is filled with clear epoxy resin.
The filling will appear dark when initially received, however light will be able to shine through when you are done cutting this down to small pieces for your knife handle.
The transparency will become evident with the smaller length pieces.
As a note: It is possible to drill a knife blank's pin holes larger (or create your own pin hole locations).
You simply need to use drill bits intended for drilling metal, which are capable of drilling through hardened high carbon steel.
This method is recommended because you be able will get the exact fit you are looking for when using our mosaic pins.
RecommendedUsesForProduct : Hunting
Style : Modern
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
UnspscCode : 52151700