Cart 2 india

Specification
AutoPartPosition : outside
Brand : Raguso
BulletPoint :
BulletPoint1 : Puller Function: The battery terminal puller makes it easy to remove the battery terminal cable, preventing damage to the battery terminals.
BulletPoint2 : Available Sizes: Puller jaws fit under cable terminals, center screw pushes down on post to pull terminals up, hardened jaws open 1/4in to 1‑1/8in to fit most battery terminals.
BulletPoint3 : Terminal Wrench Usage: 5/16in x 10mm terminal wrench is used to remove or install 5/16in side terminals, also used to remove or install 10mm battery terminals and retaining fasteners.
BulletPoint4 : Terminal Brush Purpose: Remove and dirt from battery terminals and cable clamps with this steel brush. The outer brush s the cable clamps and the inner brush s the binding posts.
BulletPoint5 : Nut Pliers Function: Nut plier is used to easily loosen and tighten nuts on battery terminal clamps, the handle is offset, suitable for working in narrow areas, and the jaws are serrated for a firm grip.
Color : Black, Silver Tone, Red, Green
ConnectivityProtocol : X-10
ControllerType : Push Button
ExternallyAssignedProductIdentifier : 5054511923544
ExternallyAssignedProductIdentifier1 : 0723534053303
ExternallyAssignedProductIdentifier2 : 723534053303
FitType : Universal
Hazmat1 : auto-grounding
Hazmat2 : UN13283
IncludedComponents : Terminal Tool - VAG
ItemName : Raguso Battery Service Tool Kit Battery Terminal Puller Steel Rustproof 7pcs High Strength Sturdy Windshield Arm Puller for Maintenance
ItemPackageDimensions_Height : 5 centimeters
ItemPackageDimensions_Length : 31 centimeters
ItemPackageDimensions_Width : 18 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : automotive-electrical-system-tools
Manufacturer : Raguso
Material : Metal,Plastic
MeasurementType : Voltmeter
ModelName : Terminal Tool - VAG
ModelNumber : a20121700ux0004
MountingType : Panel Mount
NumberOfItems : 1
NumberOfPositions : 2
PackageLevel : unit
PartNumber : Ragusoi2ocwdu8x34084
PowerSourceType : Battery Powered
ProductDescription :

EVDoctor, the #1 Expert on the Web, offers the EVSE REPAIR TOOL MAXI. A Quick Go NoGo EV Charger tester for installation or repair of Electric Vehicle Car Chargers. Fits all EV Chargers, J1772, Type1, CSS, Type2. FREE HELP. CALL US.

The EVSE Tester is designed for installation and repair of all EVSE Chargers (Electrical Vehicle Car Chargers). Just plug in the EV Charger Tester for a quick "Go NoGo" test. No additional equipment required for basic testing. The EV Charger Status is displayed on 2 LEDs - "PILOT" (green) and "1 kHz" (Pilot active, blue). For advanced testing, knowledge of EVSE operation is assumed. See resources below. A carrying case is included. (3.8"x2.8"x 1").

OPERATION -1) Insert the EVSE Tester leads into the Ground and Pilot pins of the EVSE handle. 2) and set the Connect and Charge switches Off (Left). 3) Plug in EVSE to AC Power. Observe the PILOT LED (green) On. 4) Set Connect to On (right). The PILOT LED (green) and the ACTIVE LED (blue) are On. 5) Set Charge to On. Hear EVSE audible click (power on) and the Green LED dims slightly. If there is 240V on your EVSE output it is working!

ADVANCED TESTING - Additional measurements of the Pilot "P Max" and "P Min" test point voltages can be made with a low cost digital voltmeter. The P Max and P Min represent the peaks (+ -) of the 1 kHz Pilot signal. You can estimate the charging current by measuring the DC value of the Pilot signal (See Table). Also test the "Proximity" switch in the EVSE handle for 480 ohms (latch open) and 150 ohms when pressed. A low cost digital oscilloscope is needed to measure the 1 kHz Pilot signal waveform.

RESOURCES and HELP - See listing photos for test voltages. Browse for "EV Doc Bulletin - EVSE & J1772 Handle Test Instructions." Additional information and help are provided on request by EVDoctor.

ProductSiteLaunchDate : 2022-09-03T18:59:14.450Z
Size : 17X14X4
SupplierDeclaredDgHzRegulation : not_applicable
TargetGender : unisex
TerminalType : Screw
UnitCount : 1
UnspscCode : 39121400