Cart 2 india

Specification
Brand : CONFAST
BulletPoint1 : TAMPERPROOF-Anchor cannot be removed to provide security for item being attached
BulletPoint10 : Head Style: Truss
BulletPoint2 : ZINC PLATED-Provides rust resistance for dry applications
BulletPoint3 : FOR CONCRETE ONLY-Fast, easy and strong fastening into solid concrete
BulletPoint4 : NO SPECIAL TOOLS NEEDED-Drill the hole drive with a hammer; fast and simple
BulletPoint5 : WARMBOARD Recommended-Recommended in the Warmboard-R radiant floor panel installation guide.
BulletPoint6 : Diameter: 1/4"
BulletPoint7 : Length: 1-1/2 inch
BulletPoint8 : Material: Steel
BulletPoint9 : Finish: Zinc
Color : Yellow
CompatibleGrooveDiameter : 0.375 inches
ExteriorFinish : Zinc
ExternallyAssignedProductIdentifier : 8945136167475
ExternallyAssignedProductIdentifier1 : 075352055312
ExternallyAssignedProductIdentifier2 : 0075352055312
ExternallyAssignedProductIdentifier3 : 00075352055312
FinishType : Yellow Zinc
GradeRating : Residential
IncludedComponents : Product & Instructions Guide
ItemName : CONFAST 1/4" x 2-1/2" Split Drive Flat Zinc Plated (100 per Box)
ItemPackageDimensions_Height : 2.5 inches
ItemPackageDimensions_Length : 6 inches
ItemPackageDimensions_Width : 5 inches
ItemPackageQuantity : 1
ItemShape : Block
ItemTypeKeyword : drive-anchors
Manufacturer : CONFAST
ManufacturerGrade : premium
Material : Carbon Steel Zinc Plated
MaximumShearStrength : 1248
MetalType : Alloy Steel
ModelNumber : 05531
NumberOfBoxes : 1
NumberOfItems : 100
NumberOfPieces : 100
PartNumber : SDF14212
ProductDescription : Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment
The anchor is designed for use in a Dry environment.

Head Style
The anchor is a Flat Countersunk head and is designed to prevent the head from protruding above the surface of the item being attached.

Hole Diameter/Bit Diameter
The anchor requires a 1/4" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 1/4".

Length Anchor
The length of the anchor is 2-1/2"
Minimum Embedment
The minimum anchor embedment into the concrete is 1-1/8". Therefore, the anchor must be installed so that a minimum of 1-1/8" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 1-3/8". This will ensure that the minimum embedment of 1-1/8" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/4" diameter anchor requires the hole in the fixture to be 3/8".

Spacing between Anchors
Each anchor must be spaced a minimum distance of 2-1/2" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 1-1/4" from an unsupported edge of the concrete.
ProductSiteLaunchDate : 2017-06-09T02:48:36.319Z
Scent : scent
Size : One Size
SkipOffer : 1
Style : Hammer Drive Anchors
SupplierDeclaredDgHzRegulation : not_applicable
UnitCount : 100
UnspscCode : 31161500