Cart 2 india

Specification
Brand : RATTMMOTOR
BulletPoint1 : 【Motor and TB6600 Driver wiring】Stepper motor's RED wire connects to driver's A+ port. Stepper motor's GREEN wire connects to driver's A- port. Stepper motor's YELLOW wire connects to driver's B+ port. Stepper motor's BLUE wire connects to driver's B- port.
BulletPoint10 : Driver function: 1. Hall position sensor is adopted 2. External potentiometer stepless speed regulation interface 3. Can use external analogue speed control. 4. Five-digit display speed panel 5. 220-240V OR 110-130V power supply 6. It can be externally connected with positive and reverse selection switch 7. Built-in thermal protection , Over current protection, Hall error protection.
BulletPoint2 : 【23HS8430 Motor Parameter】Phase: 2 Phase; Step Angle: 1.8 degree; Frame Size: 57x57x76mm; Shaft Diameter: 8mm; Holding Torque: 180N.cm (270Oz-in); Phase Resistance: 1ohms; Rated Current/phase: 3A; Inductance: 3.5mH+/-20%(1KHz).
BulletPoint3 : 【High Torque Stepper Motor】High quality motor steel, low self-induced reactance in the bearings, good responsiveness, direct linkage to the load at low speeds at near blocked speeds, without gear reduction.
BulletPoint4 : 【Upgraded 4.5A Stepper Motor Driver】Using the latest TB6600 new installation chip, there are low-voltage shutdown, thermal over-stop and over-current circuit protection, and compared with the TB6560 increased short-circuit protection. TB6600 driver operating voltage of DC 10-45VDC, support for sub-division of the whole step, half-step, 1/4, 1/8, 1/16 step, up to 42/57/86 two-phase / four-phase / four-wire / six-wire stepper motors within 4.2A. / six-wire stepper motor.
BulletPoint5 : 【Stepper Motor Driver Feature】The output current is steplessly adjustable to meet your various application requirements; The subdivision setting instructions are printed on the back of the board; The use of enlarged radiator ensures good heat dissipation; Adopting the common anode input mode, there are two input terminals, the wiring is more convenient.
BulletPoint6 : Holding Torque: 2.39/1.19/0.89 N.m
BulletPoint7 : Flange:80mm
BulletPoint8 : Output shaft Dia.:14 MM
BulletPoint9 : Number of Poles: 6
Color : 45mm
CustomerPackageType : Standard Packaging
Department : Unisex Adult
ExternallyAssignedProductIdentifier : 10762765818173
ExternallyAssignedProductIdentifier1 : 619191686254
ExternallyAssignedProductIdentifier2 : 0619191686254
Horsepower : 750 watts
IncludedComponents : motor and driver
ItemName : RATTMMOTOR CNC Controller Kit Nema23 Stepper Motor 23HS8430 270oz-in 76mm 3A 1.8Nm Single Shaft 57mm×57mm×76mm with TB6600 Stepper Motor Driver 4.5A DC 10-45V for CNC Router
ItemPackageDimensions_Height : 26.2128 centimeters
ItemPackageDimensions_Length : 16.1036 centimeters
ItemPackageDimensions_Width : 25.4254 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : electric-motor-controls
Manufacturer : RTM
Material : Aluminum
ModelName : QW80BL007-750
ModelNumber : 3ARED-CKIT
NumberOfItems : 2
PartNumber : 3ARED-CKIT
ProductDescription : Nema23 Stepper Motor and TB6600 Driver
ProductSiteLaunchDate : 2020-08-17T06:48:48.038Z
Size : 65mm
Speed : 6000 rpm
Style : 23HS8430+TB6600
SupplierDeclaredDgHzRegulation : not_applicable
UnitCount : 1
UnspscCode : 26111700
Voltage : 24 volts