Cart 2 india

Specification
Brand : CONFAST
BulletPoint1 : BIT INCLUDED IN EACH BOX-Proper bit equals improved holding values and reduced cost
BulletPoint2 : FLAT PHILLIPS HEAD--Can be driven with Phillips Screw Driver
BulletPoint3 : SELF-TAPPING-Taps threads directly into masonry and requires no other anchor
BulletPoint4 : DIAMOND POINT-Easier to drive the screw to save time
BulletPoint5 : Box contents: 1 x 20 pieces fischer N 5 x 40 dowels + screws for concrete, brick and natural stone.
Color : Stainless Steel
DriveSystem : Phillips
ExteriorFinish : Steel
ExternallyAssignedProductIdentifier1 : 4048962147889
ExternallyAssignedProductIdentifier2 : 04048962147889
GpsrSafetyAttestation : 1
IncludedComponents : 24 UK
ItemName : CONFAST 3/16" x 3-1/4" Flat Phillips Concrete Screw with 3 Drill Bits (300 per Box)
ItemPackageDimensions_Height : 4 inches
ItemPackageDimensions_Length : 5 inches
ItemPackageDimensions_Width : 3.5 inches
ItemPackageQuantity : 1
ItemTypeKeyword : concrete-screws
Manufacturer : CONFAST
Material : Carbon Steel - Blue Coated
Material1 : Zinc
Material2 : Nylon
MaximumShearStrength : 540
MeasurementSystem : Imperial
MetalType : Carbon Steel
ModelName : fischer - Tacos y tornillos de golpe N 5x40, tacos hormigón, Bolsa 20 uds
ModelNumber : PROFIX
NumberOfBoxes : 1
NumberOfItems : 300
NumberOfPieces : 300
PackageLevel : unit
PartNumber : CSF316314
PowerSourceType : With Manual Feed
ProductDescription : Applications
The anchor is made from Carbon Steel, and is Blue. This anchor is designed for use in Concrete, Block, and Brick.

Environment
The anchor is designed for use in a Dry environment.

Head Style
The anchor is a Flat Countersunk Phillips head and is designed to prevent the head from protruding above the surface of the item being attached.

Hole Diameter/Bit Diameter
The anchor requires a 5/32" hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Driver Required
A #2 phillips bit is required for driving the anchor into the base material.

Diameter of Anchor
The diameter of the anchor is 3/16".

Length Anchor
The length of the anchor is 3-1/4"

Thread Length
The length of the threads on the anchor is 1-3/4" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 1". Therefore, the anchor must be installed so that a minimum of 1" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 1-3/4" to 2-1/4". This will ensure that the minimum embedment of 1" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/16" diameter anchor requires the hole in the fixture to be 1/4".

Spacing between Anchors
Each anchor must be spaced a minimum distance of 3" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 2-1/4" from an unsupported edge of the concrete.
ProductSiteLaunchDate : 2017-05-23T00:00:00.000Z
Size : 3.25 inches
StreetDate : 2015-01-16T00:00:01Z
Style : Cartridge Accessories
SupplierDeclaredDgHzRegulation : not_applicable
UnitCount : 1
UnspscCode : 31161500