Cart 2 india

Specification
Brand : CONFAST
BulletPoint1 : BIT INCLUDED IN EACH BOX-Proper bit equals improved holding values and reduced cost
BulletPoint2 : FLAT PHILLIPS HEAD--Can be driven with Phillips Screw Driver
BulletPoint3 : SELF-TAPPING-Taps threads directly into masonry and requires no other anchor
BulletPoint4 : DIAMOND POINT-Easier to drive the screw to save time
BulletPoint5 : Multi-Purpose Use: From masonry projects to concrete walls, these anchors are a versatile and essential addition to your toolkit.
Color : Silver-gray or Bluish-gray
CompatibleGrooveDiameter : 1E+1 millimeters
CustomerPackageType : Standard Packaging
DriveSystem : Phillips
ExteriorFinish : Steel
ExternallyAssignedProductIdentifier1 : 008236385663
ExternallyAssignedProductIdentifier2 : 0008236385663
ExternallyAssignedProductIdentifier3 : 00008236385663
FinishType : Zinc
ItemName : CONFAST 1/4" x 2-1/4" Flat Phillips Concrete Screw with 3 Drill Bits (300 per Box)
ItemPackageDimensions_Height : 4 inches
ItemPackageDimensions_Length : 3.5 inches
ItemPackageDimensions_Width : 3.5 inches
ItemPackageQuantity : 1
ItemShape : Round
ItemTypeKeyword : concrete-screws
Manufacturer : CONFAST
Material : Carbon Steel - Blue Coated
Material1 : Stainless Steel
Material2 : Carbon Steel
MaximumShearStrength : 675
MeasurementSystem : Imperial
MetalType : Carbon Steel
ModelName : The Hillman Group 375302 Flat Head Phillips Tapper Concrete Screw Anchor, 3/16 x 2-1/4-Inch, 100-Pack
ModelNumber : 375302
NumberOfItems : 300
NumberOfPieces : 300
PackageLevel : unit
PartNumber : CSF14214
ProductDescription : Applications
The anchor is made from Carbon Steel, and is Blue. This anchor is designed for use in Concrete, Block, and Brick.

Environment
The anchor is designed for use in a Dry environment.

Head Style
The anchor is a Flat Countersunk Phillips head and is designed to prevent the head from protruding above the surface of the item being attached.

Hole Diameter/Bit Diameter
The anchor requires a 3/16" hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Driver Required
A #3 phillips bit is required for driving the anchor into the base material.

Diameter of Anchor
The diameter of the anchor is 1/4".

Length Anchor
The length of the anchor is 2-1/4"

Thread Length
The length of the threads on the anchor is 1-3/4" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 1". Therefore, the anchor must be installed so that a minimum of 1" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 3/4" to 1-1/4". This will ensure that the minimum embedment of 1" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/4" diameter anchor requires the hole in the fixture to be 5/16".

Spacing between Anchors
Each anchor must be spaced a minimum distance of 4" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 3" from an unsupported edge of the concrete.
ProductSiteLaunchDate : 2017-05-23T00:00:00.000Z
Size : 1/4"
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredDgHzRegulation1 : not_applicable
SupplierDeclaredDgHzRegulation2 : not_applicable
SupplierDeclaredDgHzRegulation3 : not_applicable
SupplierDeclaredDgHzRegulation4 : not_applicable
SupplierDeclaredDgHzRegulation5 : not_applicable
UnitCount : 100
UnspscCode : 31161500