Cart 2 india

Specification
Brand : THMOOTHER
BulletPoint1 : Thickening Clear Cover Result a Stable And Anti Yellowing Performance in Corner Mount Application, the Transparent Cover Allows the Light to Pass Through Without Reducing The Brightness. Therefore the Illumination is Brighter Than the Milky Cover.

BulletPoint2 : Cover is Easy Snapped Into the Extruded Rail, It Protect The Exposed Strip From Dust And Moisture .It is Widely Used in Lighting of Non-Eye-Direct-Viewing Areas to Achieve Good Energy-Saving Effects.

BulletPoint3 : The Channel Can Be Trimmed To Required Length Easily By Hacksaw Or Grinder,The Cover Can Be Cut By Utility Knives And Scissors,The Cover is protected by Film Initially

BulletPoint4 : The Aluminum Track Is Designed To Hold The Strip Less Than 12.1mm(0.48’) Wide ,It Fit For A Majority Of 5050 5630 2835 Steady color ,RGB RGBW Tape(not for Hue 2ND)

BulletPoint5 : The Package Included V Shape Channel 6.56FTX10 ,Clear PC Cover X10 ,Mounting Clips X40,Stainless Steel M3X12 Countersunk Screw/Carbon Steel M3X20 Screw/ Wall Anchor X40,End Caps With Hole X20 ,End cap without Hole X20

Color : Silver
ItemForm : Rigid
ItemName : THMOOTHER 10-Pack 6.56FT V Shape LED Strip Aluminum Channel with Clear Cover, Extruded Alu Track with Transparent PC Lens and Mounting Kit,Easy Cut and Installed Corner Mount Profile (10, 6.56FT)
ItemPackageDimensions_Height : 2.5 inches
ItemPackageDimensions_Length : 80 inches
ItemPackageDimensions_Width : 2.5 inches
ItemPackageQuantity : 1
ItemShape : V Shape
ItemTypeKeyword : aluminum-channels
Manufacturer : Sunny Wood
Material : 6063 Aluminum
Material1 : Aluminum
Material2 : Plastic
ModelNumber : F#3
NumberOfItems : 10
PartNumber : 1002-T
ProductDescription : Why need a channel with cover ?
1.Protect the exposed strip from Dust,Moisture and inadvertent touch,extend the lifespan of the strip
2. Provide a New Professional Clean finish to the exposed fixtures,Take your LED strips to the next level
3. A Better and Permanent Installation Method For The Led Strip For Corner ,Ceiling Etc

Steps for a DIY Lighting Project
1.Measure the width of the strip ( make sure it is not oversized in the channel ) and test it
2.Trim the channel and cover to a required length by hacksaw or other devices .
3.Peel off the sticky at the back of the strip ,lay the strip in the channel
4.Snap the diffuser into the slot of the V channel ,fix the end caps if needed
5.Screw the Mounting Clips into the working surface (Make sure the Pilot hole is in a straight Line ), Clamp the channel in the clips
6.Flush channel end to end and fix clips in the middle of the channel for extension
7.Wiring
The Strip Can be assembled after mounting the channel or away from the working site

Packing details
1.6.56FT/200CM V Shape Aluminum Channel -10 pieces
2.6.56FT/200CM Clear Cover -10 Pieces
3.Stainless Steel M3X12 Screw -40 Pieces
4.Carbon Steel M3X20 Screw With Wall Anchor -40 Pieces
5.End Caps-20 Pairs
6.Stainless Steel Mounting Clips-40 Pieces

ProductSiteLaunchDate : 2024-10-10T02:05:55.060Z
Size : 6.56FT
SupplierDeclaredDgHzRegulation : not_applicable
SupplierDeclaredDgHzRegulation1 : not_applicable
SupplierDeclaredDgHzRegulation2 : not_applicable
SupplierDeclaredDgHzRegulation3 : not_applicable
SupplierDeclaredDgHzRegulation4 : not_applicable
SupplierDeclaredDgHzRegulation5 : not_applicable
SupplierDeclaredHasProductIdentifierExemption : 1
UnitCount : 1