Cart 2 india

Specification
Brand : SÜA
BulletPoint1 : SÜA Phos-Copper 0% is a low cost brazing filler metal suitable for joining copper to copper & copper to copper alloys where critical impact or vibration stresses are not encountered in service. It should only be used on assemblies where good fitup can be maintained. Application assemblies include heat exchanger return bends, hot water cylinders and refrigeration points.
BulletPoint2 : SÜA Phos-Copper 0% is a copper rich, intermediate temperature, brazing filler metal that is moderately free flowing & self-fluxing on copper (only) by virtue of its phosphorus content. It liquates slightly more than a 7% Phosphorus Copper when heated rapidly. Induction Brazing will produce better mechanical properties in general than torch brazing. Best results are obtained with joint clearances of .001-.003”
BulletPoint3 : The self-fluxing property of SÜA Phos-Copper 0% is effective on copper only. Copper base alloys, such as brass or bronze, may be brazed with SÜA Phos-Copper 0% if the joints are coated with flux. SÜA Phos-Copper 0% should not be used on ferrous metals or nickel base allows, since the phosphorus produces brittle iron or nickel phosphides at the joint interface.
BulletPoint4 : The properties of a brazed joint are dependent upon numerous factors including base metal properties, joint design, metallurgical interaction between the base metal and the filler metal. Joints made with SÜA Phos-Copper 0% are entirely satisfactory on copper and copper alloys if good fit-up and adequate shear area are maintained.
BulletPoint5 : This kit includes a 6.5 Oz jar of our top-quality SÜA Silver-Flux #1 with a convenient brush attached to the cap for an easier flux application. Available in 9 Sticks and 1 Lb (28 Sticks) packages. Select your option from the menu.
Color : Brass
ExternallyAssignedProductIdentifier : 00840338553645
ItemDisplayWeight : 15 ounces
ItemName : SÜA - BCuP-2 PhosCopper Brazing Rod - 0% Silver - Flat - 1/8" x 0.05" x 20" (9 Sticks) + 6.5 Oz Flux
ItemPackageQuantity : 1
ItemTypeKeyword : brazing-rods
Manufacturer : Mundaka Technologies Inc
Material : Phos Copper
NumberOfBoxes : 1
NumberOfItems : 1
PartNumber : SWT-BCUP2R10X18_9R-F
ProductDescription : * Remove any oil, grease, or other contaminants from the surface to be brazed. * Apply flux to joint by dipping, swabbing or brushing area being brazed. The flux may be used as supplied or diluted. * Apply heat, by torch, induction or other means to area being brazed after flux has been applied to activate the flux. * Feed the braze alloy into the joint, unless a brazing preform is already in place. * Clean flux residues from brazed joint using hot water (60°C ± 5°C / 140°F ± 10°F) for best results. If unavailable, room temperature water may also be used. WARNING: PROTECT yourself and others. Read and understand this information. FUMES AND GASES can be hazardous to your health. HEAT RAYS, (infrared radiation) from flame or hot metal can injure eyes. Before use, read and understand the manufacturer’s instructions, Material Safety Data Sheets (MSDS), and your employer's safety practices. Keep your head out of fumes. Use enough ventilation, exhaust at the flame, or heat source, to keep fumes and gases from your breathing zone and the general area. Wear correct eye, ear, and body protection. See American National Standard Z49.1, Safety in Welding, Cutting, and Allied Processes, published by the American Welding Society, 8669 Doral Blvd., Doral, Florida 33166; OSHA Safety and Health Standards, available from the U.S. Government Office, Washington, DC 20402.
ProductSiteLaunchDate : 2022-11-09T23:44:23.593Z
Size : 9 Rods
UnitCount : 1
UnspscCode : 23271800