Cart 2 india

Specification
Brand : Generic
BulletPoint1 : 10/100 Ethernet comes standard
BulletPoint2 : Ethernet remote control and monitoring
BulletPoint3 : Minimum power of 150 Watts RMS per channel into 8 Ohm loads and 250 Watts RMS per channel into 4 Ohm loads with all channels operating
BulletPoint4 : Switch mode supply, Class-D output
BulletPoint5 : Stepped, calibrated input attenuators
BulletPoint6 : Bluetooth amplifier board includes overheat protection, circuit protection, and over-voltage and under-voltage protection to safeguard the amplifier and connected components from damage
BulletPoint7 : Mini amplifier board is built with a large heat sink, facilitating effective heat dissipation and maintaining stable performance even under high load conditions
ExternallyAssignedProductIdentifier1 : 0768447446767
ExternallyAssignedProductIdentifier2 : 768447446767
IncludedComponents : No
ItemName : ne8250pe 8-Channels Network-Enabled Class-D Power Amplifier with Protea DSP Signal Processing, Switching Power Supply, 150W RMS Per Channel Into 8 Ohm Loads, Remote Turn On/Off
ItemPackageDimensions_Height : 2 inches
ItemPackageDimensions_Length : 5.9 inches
ItemPackageDimensions_Width : 3.5 inches
ItemTypeKeyword : electronic-component-audio-amplifiers
Manufacturer : Ashly
ModelNumber : ne8250pe
NumberOfItems : 1
PartNumber : ne8250pe
ProductDescription : ne8250pe 8-Channels Network-Enabled Class-D Power Amplifier with Protea DSP Signal Processing, Switching Power Supply, 150W RMS Per Channel Into 8 Ohm Loads, Remote Turn On/Off

Connecting and controlling an amplifier for networked systems has now been simplified with Network-Enabled Amplifiers. This line offers ease of use, setup and control using standard 10/100 Ethernet protocol and Protea ne Software. No special outboard control units are needed. Choose either 4-channel ne4250 or 8-channel ne8250 amplifiers are rated at 250W per channel with separate HI-Z and LO-Z models.

KEY FEATURES
- 10/100 Ethernet comes standard
- Minimum power of 150 Watts RMS per channel into 8 Ohm loads and 250 Watts RMS per channel into 4 Ohm loads with all channels operating
- DC voltage remote gain control
- Ethernet remote control and monitoring
- Switch mode supply, Class-D output
- Stepped, calibrated input attenuators
- Remote turn on/off
- Disable all front panel controls via software
- Temperature-sensitive variable speed fan with side-to-front airflow
- 4-stage level meters
- Output current and temp indicators
- Safety/Compliance: TUV, CE, FCC,RoHS

SPECIFICATIONS
- Frequency Response: 20Hz–20kHz, (unweighted) ±1dB
- Input Impedance: 20k Ohms, Balanced
- Voltage Gain: 26dB
- Input Sensitivity: 6.2dBu
- Maximum Input Level: +21dBu
- Signal to Noise (20-20k, Unweighted): >107db
- Distortion (8 Ohm load): (SMPTE) <0.5%, (THD-N) <0.5% (20Hz-20kHz)
- Damping Factor (8 Ohms, 1kHz): >250
- Output Circuitry: Class D
- AC Main: 120VAC or 240VAC ±10% (factory set), 50–60Hz
- Power Cable Connector: 15A Edison, 3-Prong IEC
- Airflow: IN through sides, OUT through front
- Environmental: 40-120°F noncondensing
- Dimensions: 19"W x 3.50"H x 16.84"D
- Weight: 24.7 lbs


ProductSiteLaunchDate : 2024-10-22T12:55:40.914Z
SupplierDeclaredDgHzRegulation : unknown
SupplierDeclaredHasProductIdentifierExemption : 1
UnspscCode : 52161547