Cart 2 india

Specification
AgeRangeDescription : adult
Brand : Garosa
BulletPoint : Modules
BulletPoint1 : [Powerful Performance] - Equipped with a built-in ESP32 DOWD V3 chip, this control board supports clock frequencies up to 240 MHz and comes with integrated WIFI,module, and 8M bytes Flash memory chip.
BulletPoint2 : [Multiple Display Supported] - This 3D printer control board can be used with LCD2004, 12864 screens, MINI12864 V3, and TFT serial screens.
BulletPoint3 : [Wide Compatibility] - Compatible with Marlin 2.0.X firmware and supports 3D Touch for enhanced functionality.
BulletPoint4 : [Self-Contained Encoder] - Easily adjust parameters and select files with the included encoder.
BulletPoint5 : [Rgb Backlight Display] - Enjoy a customizable RGB backlight display that allows you to change the light color online.
Color : Assorted Color
CompatibleDevices : Printer
ExternallyAssignedProductIdentifier : 7310382352622
GraphicsCardInterface : integrated
IncludedComponents : No
ItemName : 3D Printer Mainboard Kit, 3D Printer Motherboard Kit RGB Backlight Display 3D Printer Control Board for TinyBee V1.0, 3D Printer Accessories
ItemPackageDimensions_Height : 7 centimeters
ItemPackageDimensions_Length : 22 centimeters
ItemPackageDimensions_Width : 14 centimeters
ItemPackageQuantity : 1
ItemTypeKeyword : 3d-printer-controllers
Manufacturer : Garosa
Material : synthetic material
MemoryClockSpeed : 240 MHz
MemorySlotsAvailable : 2
ModelName : Garosavd6k0784gc
ModelNumber : Garosavd6k0784gc
NumberOfBoxes : 1
NumberOfItems : 1
PartNumber : Garosavd6k0784gc
ProductDescription : Specification:
Item Type: For TinyBee V1.0 Main Board
Material: PCB, Aluminum Alloy
Motherboard Model: For TinyBee V1.0
MCU: ESP32 WROOM 32U
MCU Frequency: 240MHz
Memory: 520K
Input Power: DC12-24V, Heater: 2 Heater Ends And 1 Heater Bed
Temperature ADC: 3 NTC100K: TH1, TB, TH2 ( Jumper Selection Required )
Motor Interface: 5 Axes 6 Motor Interface (Dual Z Axes In Parallel)
Stepping Drive Mode: STEP, DIR Moode
Subdivision Setting: DIP Switch
LCD Interface: Support LCD 2004, 12864, For MINI12864 V3
Serial Port: For TFT Series Screen, For USART2 is reserved.
End Stop: X,Y,Z, MT DET
3D Touch: Support
Power : Support Power Reverse and Power Spike
Motor Reverse Potential: Can be absorbed by phase sequence resistor to stepper driver.
Firmware: For Marlin 2.0.X
Firmware Update Mode: U Disk Upload
Memory Card: Shipped Without Memory Card
For Mini12864 V3.0 LCD Graphical Intelligent Display
Model: For Mini 12864 V3
Material: PCB
Logic Levels: Support 3.3V, 5V Logic Inputs
Backlight Mode: For Neopixel RGB Adjustable Backlighting
Backlight Adjustment: Light: Slight Preset (For Martin)
Applicable Firmware: For Marlin 2.0, For Klipper
Applicable Motherboards: For Robin Nano V2, For Nano V3, For SgenlV1, v2, For Genl, For Robin E3

How to Use:
Used in accordance with the introduction.

Package List:
1 x For TinyBee Control Board
1 x USB Cable
1 x Display For MINI 12864 V3 Storage Card Side Insertion Board
2 x 10 Pin Color Cable
5 x A4988 Stepper Motor Driver
5 x Driver Heat Sink


ProductSiteLaunchDate : 2024-01-22T11:40:25.631Z
Size : One Size
SupplierDeclaredDgHzRegulation1 : not_applicable
SupplierDeclaredDgHzRegulation2 : not_applicable
SupplierDeclaredDgHzRegulation3 : not_applicable
SupplierDeclaredDgHzRegulation4 : not_applicable
SupplierDeclaredDgHzRegulation5 : not_applicable
SystemBusStandardSupported : SATA 2
UnitCount : 1
WaterResistanceLevel : not_water_resistant